Necklace Stand by Chain Length – 16 / 18 / 20 / 24 in Labelled Saddles, Every Pendant Hangs Free
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Necklace tree with labelled 16-24 in saddles set at computed heights: every chain ends level, every pendant hangs free.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 2
- Wydruki
- 0
- Wyświetlenia
- 23
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Bedroom
- Licencja
- Creative Commons — Attribution — Noncommercial
All images are renders. This design is digitally validated; it has not been physically printed or tested.
A necklace tree organised by chain length. Four labelled tiers - 16, 18, 20 and 24 inch (40 / 45 / 50 / 60 cm) - spiral up a faceted stem, two arms per tier. Each arm ends in a round saddle at the height computed for its chain length, so every chain ends at the same height and every pendant hangs free above the dish - no chain puddles on the dresser, and hung at their saddles no two necklaces reach each other. The octagonal dish takes rings and earrings on a lift-out tray, with a ballast trough for sand or coins underneath.
Validation status (please read): checked in CAD (hang heights, clearances between necklaces, calculated tipping) and in the slicer (no supports). It has not been physically printed or tested; chain-on-plastic friction and print mass are estimates. All pictures are renders of the CAD model with generic necklaces, pendants and rings - none is a photograph.
Features
One labelled saddle pair per standard length, inches on one arm and centimetres on the other (16 / 40, 18 / 45, 20 / 50, 24 / 60). The labels also tell you a chain's length: on its own saddle its end lands with the others.
Heights computed from the chain length (CAD check, 8 hanging points): the lowest point of every chain is at the same height (spread 0.2 mm), leaving 45 mm for a pendant and 20 mm of air above the tray. A chain with a 1 inch extender let out on the same saddle still clears the tray (at least 7 mm).
Round saddles with a 10 mm crown instead of thin hook edges. Each arm falls 15° toward its saddle, so the saddle against the 4.5 mm end flange is the lowest point of the arm.
Room for each necklace: with every loop at its saddle, every chain and pendant envelope (40 x 12 x 45 mm pendants) stays at least 12.9 mm from every other one and at least 14 mm from the stand except its own saddle (CAD check).
Every hanging point is inside the footprint, so the weight of the jewellery alone does not tip the stand (a knock still can - see Limitations).
A stepped key rib on the stem turns each tier 45° and stops it at its own height; assembled out of order, a gap shows and the cap will not seat. Two printed pins lock the column and stem.
11 printed parts, no supports, no hardware.
Dimensions
405 mm tall, 180 mm octagonal base (across flats) with a 20 mm dish rim. Saddle tops at 274.2 / 299.7 / 325.1 / 375.9 mm (16 / 18 / 20 / 24 in). 8 arms, 45° apart, 72 mm hang radius. Capacity: 8 necklaces, 2 per length.
Which files?
Ready-to-print PrusaSlicer projects (parts placed, settings embedded; generic 220 x 220 mm profile - switch to your printer, press Arrange, slice):
pendant-line_p1_base_PLA - base dish (about 116 g, 7 h 46 min)
pendant-line_p2_column_PLA - column, lying diagonally, 4 mm brim (about 49 g, 3 h 31 min)
pendant-line_p3_tray-stem-pins_PLA - tray, stem, 2 pins (about 77 g, 5 h 3 min)
pendant-line_p4_tiers-cap_PLA - tiers 16 / 18 / 20 / 24 and the gem cap, in an accent colour (about 127 g, 10 h 57 min)
STL files of all 11 parts.
model.py - the CadQuery source: chain lengths and labels, pendant allowance, air gap, saddle radius, arm slope.
Print settings
PLA - matte stone or white for the body, a silk gold or champagne PLA for the tiers and cap looks best. PETG also works.
0.4 mm nozzle, 0.20 mm layers, no supports, oriented as in the projects: base and tray flat, column and stem lying on a flat face, tiers flat on their arms, cap upright.
About 370 g and 27 h 18 min in total (PrusaSlicer 2.9.6 estimates on a generic profile - faster printers need less time).
Assembly
Ballast (recommended - the stand is light without it): fill the trough in the base evenly with coins or steel washers, or with dry sand in a small bag (loose sand can trickle through the tray gap), no higher than the ledges; lay the tray on the ledges. The tray comes out again only with the stand taken apart.
Push the column onto the base spigot so the pin holes line up and tap a pin through (a snug fit; push it out with a 2 mm rod).
Push the stem's tenon into the column top (it only fits one way) and tap the second pin through.
Slide the tiers down the stem in order 16, 18, 20, 24, numbers upright and the round saddles on top: each notch follows the key rib and each tier stops at its own step (if a tier catches on a step, twist it slightly).
Press the gem cap on top.
How to use it
Close the necklace's clasp and hang the loop over the end of the arm with its number, so it rests in the saddle against the end flange. A loop left part-way along the arm stays there - push it out to the flange. Chains between two lengths go on the next longer label (a 22 in chain goes on 24). Lift necklaces straight up to take them off.
Limitations
Lengths 16 / 18 / 20 / 24 in (40 / 45 / 50 / 60 cm). Longer opera or rope chains (28-36 in) do not hang free; a chain on a shorter label than its length will touch the tray.
Pendants up to about 40 mm wide and 45 mm long (bail to bottom) were checked; larger statement pieces and bib necklaces may touch. Meant for light everyday necklaces.
Snake and herringbone chains are best stored flat.
A tall, light stand: a sideways push of about 0.7 N at the top tips it empty, about 1.1 N with the trough filled with sand (calculated). Fill the ballast trough and place it where it will not be knocked.
Not physically printed or tested.
Pictures
Renders of the CAD model, not photographs: the dressed stand on a dresser (cover), the level line where every chain ends, a saddle close-up, the stand alone, the kit exploded in assembly order and the dimensions. Jewellery is generic.