Spiral Crown Vase – Designed to Fit LEGO Botanicals Bouquets, a Guide Tube for Every Stem
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Two-part vase for brick-built bouquets: 19 holes on a golden spiral, each with a guide tube that holds the stem's angle.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 4
- Wydruki
- 0
- Wyświetlenia
- 23
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Home Decor
- Licencja
- Creative Commons — Attribution — Noncommercial
A two-part, two-colour display vase for brick-built flower bouquets, designed to fit LEGO® Botanicals bouquets. A 182 mm vessel with a thin twisted-flute skin holds a crown insert that sits flush in its rim. The crown has 19 (or 12) holes on a golden spiral, and below each hole hangs a guide tube along that stem's own computed angle, closed at the bottom. Push each stem down its tube until it stops: the tube holds it over its whole buried length, so every stem keeps its designed angle and its place. Filled from the centre outwards, equal-length stems open into an even, slightly turning dome (computed in CAD); mixed bouquets are arranged by you.
Validation status (please read): designed from published LEGO system dimensions and LDraw part geometry and checked in CAD and in the slicer (no supports). It has not been physically printed or tested, and not tried with real bricks - the fit is designed, not shown. Print the fit coupon first. All images are renders of the CAD model; the flowers are generic brick-style props made for the renders - none is a photograph.
Features
One guide tube per stem, closed at the bottom: 4.8 mm axle stems, 3.2 mm bar stems and joiner-chain stems (up to about 7.3 mm) each slide down their own tube and keep their angle (CAD angle play at most about 2.4° for an axle, 3.5° for a bar, 0.6° for a joiner chain).
Two crowns, one vessel: Bouquet 19 for mixed bouquets (1-19 stems) and Roses 12 for the 12 big rose heads of a rose bouquet (~216 mm stems). In CAD the closest flower centres of equal stems are 44 mm apart (Bouquet 19) and 48 mm (Roses 12).
Harder to knock over than a slim vase: a wide 117 mm foot and a ballast bay below the tubes. Calculated push to tip at 300 mm height: 1.8 N with a 300 g ballast bag, 1.2 N empty (a slim 8 cm vase with the same bouquet: about 0.6 N, calculated the same way).
Two support-free prints in two colours - no glue, screws or magnets. Only one sensible way in (tubes down); rotation does not matter.
A small fit coupon (about 1 h, 10 g) with one vertical and one 30° bore: push a joiner-chain stem through both before the long prints.
Dimensions
Vessel 182 mm tall, 117 mm foot, 111 mm rim, 2 mm fluted wall. Crown insert 99.4 mm across, 85.6 mm deep including the tubes. Bores 8.1 mm. Stems lean about 30° (Bouquet 19) and need about 100 mm of bare stem at their bottom end.
Which files?
Ready-to-print PrusaSlicer projects: spiral-crown-vase_bouquet19_complete.3mf and spiral-crown-vase_roses12_complete.3mf (vessel + crown insert, 2 beds), or the single plates: plate0_fit_coupon (print first), plate1_vessel (both kits), plate2_bouquet19_crown_insert, plate2_roses12_crown_insert.
STL files: vessel, Bouquet 19 insert (spiral-crown-vase_insert), Roses 12 insert, fit coupon.
model.py - the CadQuery source: hole count, lean, twist and stem length.
Print settings
PLA (matte); PETG if the vase stands on a sunny windowsill (PLA softens around 55 °C). Two colours: vessel in the main colour, crown insert in an accent colour.
0.4 mm nozzle, 0.20 mm layers, no supports.
Vessel upright on its foot. Crown insert top face down (the visible face gets the bed finish), tubes pointing up, with small-perimeter speed 25 mm/s (preset in the projects; set it by hand in other slicers - at 15 mm/s the insert takes several hours longer).
Vessel about 12 h / 192 g; Bouquet 19 insert about 9 h 45 min / 95 g; Roses 12 insert about 7 h / 72 g; fit coupon about 1 h / 10 g (PrusaSlicer estimates, generic profile).
If the coupon's bores are tight, print the insert with a small negative XY size compensation (e.g. -0.1 mm in PrusaSlicer) or raise hole_d in the source. The coupon checks the bore size, not the straightness of long chains.
Assembly
Optional: put a bag of sand or rice (300-500 g) in the bottom of the vessel as ballast.
Drop the crown insert into the rim, tubes down; its top sits flush with the rim.
Move or remove leaves and clips from the lowest ~100 mm of each stem. Push each stem down a hole until it stops, starting with the hole nearest the centre - tall stems inside, shorter ones outside. If a stem does not drop in, tilt it the way its hole leans. Turn each stem so its flower faces the way you like (the round bores let stems turn).
Dry display only - no water, no real flowers. To empty: lift the stems out, then tip the vase over slowly onto a towel; the insert and the ballast bag slide out. Dust in empty tubes: turn the insert over and shake it.
Limitations
Not physically printed and not tried with real bricks.
The even dome is computed for equal stem lengths; real bouquets have mixed lengths and flower sizes, so the final arrangement is up to you. Heads larger than the spacing will touch.
Stems turn freely in their round bores (by design).
Each stem needs about 100 mm of bare stem; leaves or clips lower than that stop it early.
Not watertight. Stability figures are calculations (bouquet 500 g, centre of mass 110 mm above the rim, 15 mm off-centre).
LEGO® is a trademark of the LEGO Group, which does not sponsor, authorise or endorse this design.