1 / 8
Blackout Blind for Narrow Door Glass – Crank Roller, No Cord or Chain, Sealed Side Rails — zdjęcie 1
1 / 8

Blackout Blind for Narrow Door Glass – Crank Roller, No Cord or Chain, Sealed Side Rails

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Slim crank-driven blackout roller for the narrow frosted strip in modern doors: sealed side rails, captive bar, no cord.

Ocena
0 / 5
Polubienia
2
Pobrania
0
Wydruki
0
Wyświetlenia
12
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

A slim blackout roller blind for the tall, narrow frosted glass strip in many modern doors (about 160 x 1560 mm visible glass, e.g. Westag LA-1 / LOBO LA 008 light cut-outs). A printed head (58 mm tall, 38.4 mm deep) sits on the flat door face above the glass. A small crank disc turns a gear pair that drives the roll both ways; a felt brake holds the blind at any height; an adjustable stop nut ends the travel at the closed position. Bought blackout fabric runs with both edges inside two aluminium U-rails taped on the glazing beads, and the bottom bar's steel rod runs captive inside the rails, so the bar cannot swing or slap the glass when the door slams. No cord, no chain, no loop, no magnets. A print + buy kit.

Validation status (please read): designed and checked in CAD and in the slicer; brake holding, gear strength, slot drag and light leakage are calculated or assumed. It has not been physically printed, assembled or tested. All pictures are renders of the CAD model with bought-part stand-ins, or drawings - none is a photograph. The night pair is an illustration of the intended state, not a measurement.

Features

  • No cord, chain or loop in any position; the crank arm folds flush into the disc and is held there by a detent.

  • Sealed edges: the fabric edges run inside aluminium U-rails with black felt on the web; in the CAD plan section the edge light has no straight path (0 of 4,510 test rays get through). Light blocking itself has not been measured; a faint glow can remain at the corners.

  • Captive bottom bar: its 5 mm steel rod runs in printed shoes inside the rails - no swinging, no hold-down clips.

  • Positive crank drive both ways plus an adjustable bottom stop nut: once the stop is set, the fabric cannot be over-wound past closed.

  • Slim: 38.4 mm head (about 39.5 mm from the door with the mounting tape), crank folded; rails 18.1 mm.

  • Holds at any height (felt brake, calculated at 2x the worst roll torque); light effort (calculated): about 4.8 N to raise and 1.9 N to lower at the grip; about 14 crank turns from open to closed.

  • The crank disc is held by a printed cap and one screw; the fabric can be replaced in place.

Will it fit my door?

  • Ready kits: the glazing bead must lie under the whole rail - visible glass width W up to 172 mm with W/2 + bead width of 96 mm or more (22 mm beads: W 148-172 mm; 25 mm beads: W 142-172 mm), beads about 5 mm proud, glass height up to 1650 mm. Only the bought lengths change with the height.

  • Other doors: change the parameters in model.py (glass width 90-166 mm, glass height 600-1650 mm, bead width 15-25 mm, bead height 0-6 mm, crank left or right) and export again; it rejects sizes outside the checked range.

  • A flat frieze of at least 59 mm above the glass. Put the crank on the side away from the hinge, at least 20 mm from the leaf edge or frame. On an LA-1 door the crank sits about 1.85-1.9 m above the floor (overhead cranking).

Which files?

  • crank_blackout_roller_160mm_glass_crank_LEFT_complete.3mf and ..._crank_RIGHT_complete.3mf - the complete kit (16 pieces) on ONE 220 x 220 mm plate each, brims and 4-perimeter gear parts set. Crank left / right as seen from the room.

  • crankLEFT_*.stl / crankRIGHT_*.stl - every part on its own (print the fascia, lip rail and bar body separately if your printer warps long parts).

  • model.py + calc_mechanism.py - the parametric CadQuery source.

Print settings

  • ASA, black or anthracite, for every part (behind glass the parts can reach 46-76 °C in sun - PLA and PETG soften too low). Enclosed printer and good ventilation.

  • 0.4 mm nozzle, 0.2 mm layers, 15 % gyroid, 3 perimeters (4 on the gear and pin parts), no supports - as placed in the projects.

  • About 16 h 47 min and 183 g per complete plate (PrusaSlicer 2.9.6 estimate on a generic profile). PrusaSlicer shows a "thin fragile part" stability note for the fascia (5 mm brim set).

Bought parts (for the 160 x 1560 mm kit)

Rough cost of all bought parts about EUR 50-75 at typical EU DIY prices (an estimate, not a quote).

  • Blackout fabric, PVC-laminated or coated, at most 0.35 mm thick (10 layers folded must measure 3.5 mm or less), white back: 183 x 1727 mm (length = glass height + bead width + 145 mm).

  • Aluminium tube 16 x 1 mm: 185 mm.

  • Aluminium U-profile 12 x 10 x 1.5 mm, 2 m stock: 2 x 1604 mm (glass height + bead width + 22 mm).

  • Threaded rod M6 (DIN 976): 249 mm; 4 M6 nuts (DIN 934).

  • Thrust bearing F6-12M (6 x 12 x 4.5); compression spring OD 10-11 mm, ID at least 6.5 mm, free length about 15 mm, 5-6 N/mm; washer M6 DIN 9021 (6.4 x 18 x 1.6); felt ring 7 / 18 x 1 mm.

  • Steel rod 5 mm: 184 mm (optional ballast: steel flat 10 x 3 x 158 mm). Steel pin 1.5 x 22 mm.

  • Countersunk self-tapping screw ST2.9 x 6.5 (DIN 7982); optional 2 countersunk wood screws 3.5 x 30 (idle block on a solid-timber frieze); optional 0-3 shim washers DIN 988 6 x 12 x 0.5.

  • 1 mm black self-adhesive felt, 2 mm black foam strip, black acrylic-foam tape about 1.1 mm, thin double-sided tape, fabric glue, 2-part epoxy, medium-strength threadlocker, a drop of CA glue.

  • Tools: hacksaw, file, caliper, 1.5 mm drill, screwdrivers, isopropyl alcohol.

Assembly (summary - read each step before you start)

  1. Measure the glass, bead width and how far the beads stand proud; check the fit range and the fabric thickness. Pick the crank side away from the hinge.

  2. Cut: tube 185 mm; M6 rod 249 mm (file the ends, run a nut over each); both U-profiles 1604 mm (deburr); 5 mm rod 184 mm; fabric 183 x 1727 mm, square. Trim both bottom fabric corners: 6.5 mm off each side over the bottom 48 mm, so only the 170 mm middle wraps the rod.

  3. Roll: epoxy a tube plug into each tube end. Tape the fabric's top edge square along the tube, white side toward the glass, leaving the roll on the door side; wind it on.

  4. Bar: wrap the trimmed bottom end once round the middle of the 5 mm rod and glue it (25 mm hem); slide rod + hem into the bar's channel and centre it; optional steel flat in the ballast pocket; push a shoe onto each bare rod end; felt strips in the shoe recesses, felt dots on the bar's top posts.

  5. Rod: push the M6 rod through both plugs, threadlock a nut onto each end and seat it in the plug's hex pocket. Set the rod to stick out 14.6 mm beyond the control-end flange and 36.5 mm beyond the idle-end flange (±0.3 mm), then let it cure.

  6. Control end: epoxy the DIN 9021 washer onto the bushing wall in the pinion pocket (centre it with the rod); glue the felt ring to the pinion's plain face and press an M6 nut into its hex pocket. From the open back of the control block: thrust bearing into its seat, spring into the bore, pinion into its pocket (felt toward the washer).

  7. Head: epoxy the fascia onto the control block's tenon; stick a felt strip inside the fascia's bottom edge at the slot. Lay the roll in from the open back, fabric and bar hanging out of the bottom. Push the rod through the bushing, threadlock the tip and turn the roll to screw the rod into the pinion nut until the plug flange is 0.5 mm from the block.

  8. Idle end: stop nut into the chamber, slide the idle block onto the rod's idle end, spin the nut on, seat the block on the fascia (do not glue it).

  9. Lip rail: from the door side, push it into the bottom of the head between the door side and the fabric, rounded lip toward the room, until both ends sit in their pockets. The fabric now runs over the lip and down through the 2 mm slot.

  10. Crank: drill the disc's pin hole with 1.5 mm, pin the unfolded arm in its groove (a drop of CA). Put the disc on its post (teeth meshing), drop the disc cap in, drive the ST2.9 x 6.5 screw snug - the disc must still turn freely. Fold the arm into its detent.

  11. Mount the head: clean the door with isopropyl alcohol, foam tape on both end blocks, the lip rail's tape land and the fascia's top land; press the head on level, 1 mm above the top bead (on a solid-timber frieze the idle block can take two screws too).

  12. Rails: felt inside each U's web; foam tape on one 10 mm leg; offer each rail from the outside over the shoe and fabric edge, top 1 mm under the head; crank the bar down slowly and use it as the spacing gauge (shoes at least 1 mm from the felt), pressing the tape as you go. Glue a U end cap into each rail's bottom.

  13. Bottom stop: crank down until the shoes rest on the end caps, take the stop cover off, spin the stop nut until it touches the chamber end (crank-left kit: the end farther from the glass; crank-right: nearer), press the cover back in. Check: up 2 turns and down - it must stop firmly. If raising is blocked or lowering does not stop, move the nut to the other end.

Brake creep: if the blind slowly creeps down, slip one DIN 988 shim behind the thrust bearing (up to 3). Use: unfold the arm (it stops at about 106°) and crank; let go at any height; do not force past the bottom stop; stop cranking when the bar meets its bumpers under the head (there is no top stop). Fold the arm back flush after use.

Limitations

  • Not printed, assembled or tested. Do a dark-room torch test after installing - a faint glow can remain at the corners (slot ends, rail tops, bar ends).

  • Ready kits fit only the range above; fabric 0.35 mm or thinner.

  • Taped parts depend on the door surface: do a pull test; never screw into plastic clip beads or hollow-core door skins.

  • Do not force the crank at the ends of travel: the printed face-gear teeth carry the full crank torque and have no slip clutch. Turn the crank by its grip; nothing holds the arm open.

  • The stop cover is a light press fit - if it is lost, the bottom stop is gone.

  • More parts, more cost and more work than a chain cassette blind or a cord-free honeycomb blind - this kit is for people who want no chain and sealed edges and a captive bar.

  • Designed with reference to the no-cord principles of EN 13120 / ANSI-WCMA A100.1; not tested or certified to any blind-safety standard.

Pictures

Renders of the CAD model and drawings, not photographs: the blind 75 % closed on a modern door (cover), the strip open vs closed at night (illustration, not measured), open, half open, the crank close-up, the head exploded on a door slice, the dimensions and the side-channel section. Westag, LOBO and LA-1 are named only as fit references; not affiliated.

Tagi