1 / 7
Fungus Gnat Trap Leaf for Houseplants – Holds a Yellow Sticky Card Just Above the Soil, 12/15/19 cm — zdjęcie 1
1 / 7

Fungus Gnat Trap Leaf for Houseplants – Holds a Yellow Sticky Card Just Above the Soil, 12/15/19 cm

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A printed leaf that lies on the soil and holds a yellow sticky card 10 mm above it, where fungus gnats come out.

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
19
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

A curved, printed leaf that lies on the potting soil along the pot wall, beside the plant, and holds a piece of a double-sided yellow sticky card flat, 10 mm above the soil - where fungus-gnat adults come out. Three short legs end in stop pads that keep that gap, with small spikes that grip the mix. The leaf's midrib and veins form an open lattice: the yellow shows between the veins and gnats can reach the upper glue face through the slots, while the lattice keeps fingers and leaves back from it. The lower glue face looks straight down at the soil. The leaf stem is the handle for lifting it off.

Validation status (please read): digitally validated only - checked in CAD and in the slicer. It has not been physically printed or tested, and not tried in a real pot; the catch rate in this low, horizontal position has not been measured. All pictures are renders of the exported model or diagrams computed from it; the pot, soil, plant and card are stand-ins, and no gnats are shown caught - none is a photograph.

Why low and flat?

Fungus gnats breed in damp potting mix and the adults stay near the soil surface. The usual home trap is a yellow card on a stake, standing upright with its glue in full view, where it catches leaves, hair and fingers; a card laid straight on the soil sticks to it and gets soaked. Horizontal traps facing the soil are a known grower method - this leaf brings it to houseplant pots: low, flat and shielded, and it reads as part of the plant.

Features

  • The card sits 10 mm above the soil; the stop pads keep that gap even when the leaf is pressed down or the mix settles.

  • Shielded, not hidden: the vein lattice keeps the upper glue face back from casual contact while the yellow stays visible. Catches show through the slots.

  • Curves along the pot wall beside the plant - no stake in the root ball, nothing upright to knock over.

  • Use any double-sided plastic yellow sticky card: cut a piece along the printed template; it holds by its own glue on a continuous rim - no clips.

  • One part plus a flat template, no supports, about 7-14 g. Covers about 11-14 % of the soil, so the rest can still dry.

Which size?

Measure across the soil surface, not the rim (thick-walled ceramic pots have less soil area - pick the next smaller size).

Size

Soil surface needed

Room for the plant in the middle

Leaf (as printed)

Card piece

12 cm

106 mm or more across

single stem or crown up to 38 mm

51 x 79 x 16.5 mm

25 x 58 mm

15 cm

136 mm or more

crown up to 50 mm

60 x 98 x 16.5 mm

35 x 80 mm

19 cm

176 mm or more

crown up to 70 mm

72 x 127 x 16.5 mm

47 x 109 mm

In use the leaf stands 12 mm high. A 19 cm pot can take two leaves, one on each side of the plant (pair project). Other pot sizes: python model.py --set rim_d=170 (plus stem_clear for the plant room) - only the presets were checked.

Which file?

  • gnat-trap-leaf_12cm_PETG.3mf / _15cm_PETG.3mf / _19cm_PETG.3mf - leaf + template on one plate, ready to print.

  • gnat-trap-leaf_19cm_pair_PETG.3mf - two leaves + template for a large pot.

  • gnat-trap-leaf_15cm_discreet_PETG.3mf - a solid-top leaf that hides the card completely; it catches only from below. Use it where looks matter more.

  • STL files of every leaf and template, and model.py (CadQuery source; Python 3.10+ with cadquery, trimesh, shapely and numpy).

Print settings

  • PETG (it lives on damp soil); PLA can be used indoors. Sage green or terracotta to match the pot.

  • 0.4 mm nozzle, 0.20 mm layers, no supports. As exported: the leaf's top face flat on the bed (a textured PEI sheet gives a matte face and lets it flex off), template flat beside it. 3 perimeters, 20 % infill and "avoid crossing perimeters" (no strings under the card) are set in the projects.

  • 42 min / 6.5 g (12 cm), 56 min / 9.6 g (15 cm), 1 h 19 min / 13.9 g (19 cm) - PrusaSlicer estimates on a deliberately slow generic profile.

Setup and use

  1. Lay the template on the card (liners still on), trace round it and cut the piece out with scissors. From a 25 x 10 cm card you get about 12 (12 cm), 6 (15 cm) or 4 (19 cm) pieces; from a 20 x 15 cm card about 15, 8 or 4.

  2. Peel both liners. Turn the leaf over, press the piece into the fence ring under the veins, and press along the edge so the glued rim holds it.

  3. Turn it back over and set it on the soil along the pot wall, beside the plant.

  4. Water the open side of the pot, or lift the leaf off by its stem first (set it down on its legs so the lower glue stays off the table).

  5. Change the card piece when it is covered or dusty, typically every 1-2 weeks. Glue on the veins: wipe with vegetable oil, then wash with dish soap.

Sticky traps catch adult gnats; the larvae live in the soil. Pair the leaf with the usual care advice: let the top of the soil dry between waterings, and use Bti or beneficial nematodes for a heavy infestation.

Limitations

  • Not physically printed or tested; catch rate not measured, and no comparison with upright cards is claimed. It monitors and catches adults; it does not remove an infestation by itself.

  • The underside glue face is open to the soil (that is where it catches). Hair, whiskers or a paw can still reach the glue - keep it out of pots that cats dig in or chew. If glue gets on fur, use vegetable oil and ask a vet if needed.

  • Needs free soil beside the plant; not for pots whose stems fill the surface.

  • Top-watering over the leaf wets the card - lift it off or water the open side. Paper cards soften when wet; use plastic cards.

Pictures

Renders of the exported model and diagrams, not photographs: the leaf on the soil beside a houseplant (cover), the leaf on a slab of potting mix, the leaf with its card piece, the three sizes in their pots, the leaf alone, the underside and the dimensions.

Tagi