Thick Cutting Board Drying Stand – Pair of Feet for End-Grain & Butcher-Block Boards 25.5–64 mm
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Two sculpted feet hold a thick wooden cutting board upright on its edge to dry; six sizes for boards 25.5-64 mm thick.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 12
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Kitchen
- Licencja
- Creative Commons — Attribution — Noncommercial
Two printed feet hold a thick wooden cutting board upright on its edge to dry. The board's two bottom edges rest on steep seat flanks with its bottom face in the air, and it settles a few degrees onto one rounded nose.
Measure your board's thickness and pick the size whose band contains it: 32 (25.5-32 mm), 38, 45, 51, 57 or 64 (57.5-64 mm). Each foot is 172 x 95-98 x 18 mm; the pair prints on one 220 mm plate (180 mm beds: one foot at a time).
Validation status (please read): digitally validated only - fit, contacts, drainage, strength and stability are calculated from the CAD. The feet have not been printed or tested with a real board. All images are renders of the print files with a generic proxy board, or drawings - none is a photograph.
Features
Made for thick boards: six sizes cover end-grain and butcher-block boards 25.5-64 mm thick - the board racks we found stop at about 25-31 mm. The nose gap is always the size + 3 mm, so a board that swells about 1 mm when wet still drops in.
Dries on edge, touching very little: the board rests on two short edge lines and at most one rounded nose point. Its bottom edges sit about 25-34 mm above the worktop; in the CAD check no printed surface comes within 2.9 mm of the board farther than 8 mm from a contact.
Drains: every top surface of the empty foot falls toward a diamond drain eye or off the toes - a pooling check on the CAD finds no basin on any size. With a board in place, a little water sits in the narrow wedge along each contact line until it dries.
Settles predictably: for a board lowered roughly upright, a frictionless calculation gives one rest position per size - about 2-2.5° at the thick end of the band and 5.5-6.5° at the thin end.
Wide stance: the outer pad edges sit about 85 mm out each side.
One ribbon-like sculpted profile per foot; the pair prints flat, no supports, no hardware.
Sizes
Size | Board thickness | Nose gap | Board's bottom edges above the worktop |
|---|---|---|---|
32 | 25.5-32 mm | 35 mm | 25.2-30.8 mm |
38 | 31.5-38 mm | 41 mm | 25.7-31.4 mm |
45 | 38.5-45 mm | 48 mm | 26.4-32.0 mm |
51 | 44.5-51 mm | 54 mm | 26.9-32.5 mm |
57 | 50.5-57 mm | 60 mm | 27.4-33.0 mm |
64 | 57.5-64 mm | 67 mm | 28.0-33.7 mm |
A board on a boundary (e.g. 45 mm) fits either size; in the smaller size it leans less. Other thicknesses: the parametric source - set T to your measured thickness + 1 mm (T 30-66).
Stability (calculated, frictionless, not measured)
Sideways push at the top of the board that tips board and feet together: about 9.7 N for a 6 kg, 51 mm board (432 mm tall) in size 51; about 15.7-16 N for an 8 kg board at the top of each band. A light, tall board stood on its short edge (450 mm tall, 2.2 kg at 30 mm) at the thin end of each band: about 3.1-5.4 N (2.5 N for a 25.5 mm board in size 32). Standing a board on its longest straight edge roughly doubles the margin for light, tall boards.
Files
thick-board-drying-feet_<size>_complete_PETG.3mf - one ready-to-print PrusaSlicer project per size, both feet on one 220 x 220 mm plate, settings embedded.
foot_size32.stl … foot_size64.stl - one foot per size (print two).
model.py - the parametric CadQuery source; it refuses geometry that would not fit the bed or would leave the floor too thin. Only the six sizes were checked.
Print settings
PETG (or ASA). Print solid - 4 perimeters and solid rectilinear infill, as embedded: the floor-bending and horn-strength checks assume a solid part.
0.4 mm nozzle, 0.20 mm layers, no supports, lying flat (18 mm tall) as placed. The whole profile is a thin first layer: use a textured PEI sheet or a release layer such as glue stick on smooth PEI, and add a 3 mm brim if your bed holds PETG poorly.
A pair takes about 7 h 41 min - 8 h 31 min and 119-137 g on a slow generic profile; the size-51 pair about 3 h 27 min / 127 g on a Prusa MK4S (0.20 mm SPEED) - PrusaSlicer estimates.
Optional: thin flat self-adhesive bumper dots (6-8 mm, at most 1 mm thick) against sliding - two per pad, side by side, at the outer end of each pad next to the toe.
How to use it
Put the two feet on the worktop, parallel, about a quarter of the board's length in from each end (at least 70 mm in, clear of any bun feet).
Set the board on edge into them, longest straight edge down, lowering it roughly upright (lowered at a strong tilt, a thick board can catch on the noses - straighten it and it drops in). It settles a few degrees onto one nose.
Lift it straight out. An empty foot is light and only 18 mm deep, so it tips over easily along the board's length - stand it back up before setting the board in. Wipe the feet now and then.
Limitations
Not printed or tested with a real board.
Sized by thickness: a board thinner than the band leans more; a board up to about 3 mm thicker than the size rests high and can wedge if pressed down - use the next size up.
The board's edge stays wet a little longer where it rests on the feet. No drying-time or hygiene claim.
Not a rack for thin boards, dishes or knives. Boards over about 8 kg are outside the strength checks. Hand-wash; PETG is not made for hot dishwasher cycles.
Pictures
Renders of the print files and drawings, not photographs: a thick board standing in the feet on a worktop (cover), the empty pair, how it holds the board, the six sizes, the dimensions, the print plate and the drain eye. The board is a generic proxy.