1 / 6
CYM Case Hosyond-S3-35 – Hosyond 3.5" ESP32-S3 Touch Display Case (battery + GPS + speaker, Standard and Slim) — zdjęcie 1
1 / 6

CYM Case Hosyond-S3-35 – Hosyond 3.5" ESP32-S3 Touch Display Case (battery + GPS + speaker, Standard and Slim)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This 3D-printable, two-part enclosure houses a **Hosyond 3.5" ESP32-S3** capacitive touch display board

Ocena
0 / 5
Polubienia
1
Pobrania
22
Wydruki
0
Wyświetlenia
114
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

If you like my design and plan to download it, please show your appreciation by giving it a like!!

SUMMARY / DESCRIPTION

This 3D-printable, two-part enclosure houses a Hosyond 3.5" ESP32-S3 capacitive touch display board (ES3C35P, 320×480) for the Cheap Yellow Monster (CYM) firmware — https://github.com/JimGat/CYM (select the board as Hosyond ES3C35P 3.5 in the Web Flasher). It turns the bare board into a pocket device with its own battery, GPS and speaker.

Two models, one front cover

- Standard (case 15.0 mm): with the speaker from the board set, facing a grille in the back.

- Slim (case 12.9 mm): no speaker, thinner.

What fits inside

- The Hosyond 3.5" ESP32-S3 board (54.5 × 101.5 mm), held by 4 × M3 screws (6–7 mm) into M3 brass hex standoff nuts (5 mm) in the case posts — the same screws and nuts as in the CYM NM-CYD-C5 and 2432S028R cases; they are not included in the Hosyond set

- A 1100 mAh LiPo battery, 53 × 30 × 7.5 mm, plugged into the board's own BAT socket — the board charges it over USB-C; no extra charge module needed

- An ATGM336H GPS module with its antenna, on the board's UART socket

- The 40.5 × 28.5 × 10 mm speaker from the board set (Standard only), on the SPK socket

- An SS12D00G slide switch in the battery lead

Features

- Flexible BOOT and RESET buttons on the back face

- Roofed pocket for the GPS antenna; pockets for the battery, GPS module, speaker and switch

- Hex nut pockets with small crush ribs that hold the nut

- Holes for the RGB LED and the GPS LED; speaker grille (Standard)

- Side openings for UART, I2C, EXP.INT, microSD and USB-C; engraved labels

Printing

- Two parts per model, printed flat, no supports

- Standard: 57.4 × 105.4 × 15.0 mm + front cover 3.9 mm (18.9 mm total); Slim: 12.9 + 3.9 = 16.8 mm

- About 21–24 g of PLA; roughly 3 h (Standard) / 2 h 30 min (Slim) for both parts together

- Full slicer settings are in the Print Settings below and in the manual

Assembly

Full illustrated instructions are in the attached manual (EN / TR / DE, PDF).

License: CC BY-NC-ND 4.0 — you may print and use the case yourself and share the unmodified files with credit. Selling printed cases or the files, commercial use and publishing modified files are not allowed without permission. The CYM firmware is a separate project with its own license.

CYM Case Hosyond-S3-35 · Revision 1 · Designed and made by @birolt29 @alen29

PRINT SETTINGS

- Printer brand: Creality

- Printer: Ender-3 S1 Pro

- Rafts: No

- Supports: No

- Resolution: 0.16 mm

- Infill: 15%

- Filament brand / color / material: SUNLU / Black / PLA (PLA+)

- Notes:

0.4 mm nozzle. 3 walls (Arachne / variable line width), outer wall first, outer-wall speed 30 mm/s. Nozzle 210 °C (first layer) / 205 °C, bed 60 / 55 °C. Elephant-foot compensation 0.1 mm. No supports anywhere. Case: flat closed back face on the plate, open side up. Front cover: lettered front face on the plate. Dry the filament before printing so small lettering does not fill in.

Tagi