Vaporesso XROS Magnetic Pod Holder - CUSTOMISABLE for 1 to 6 Pods
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Keep your pods tidy instead of having them sticking to each other in a heap!
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 8
- Wydruki
- 0
- Wyświetlenia
- 30
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Organizers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Designed for XROS pods with 11.7x22mm in the lower part of the tank that will fit into the holder, the wider shoulder being at least 10mm from the base of the pod. I use XROS CoreX 3.0, but 2.0 is the same size and may well be the same size as other XROS pods too, just check your measurements.
I originally downloaded the following model...
https://www.printables.com/model/675652-xros-pod-holder-with-magnets
...but after printing out sections of it to test the fit with pods and magnets, I realised it wasn't quite right. The pod holes are a bit too big, and the magnet holes are too small, so a simple scaling wouldn't fix both issues. Doing major edits on STLs can be quite tricky in Fusion because converted faces often end up still as triangles when you try to operate on them, and the edges are all tiny little bits instead of lines and curves, so I started completely from scratch using the original design idea but with all my own measurements. While I was at it, I made it customisable, so if you load the F3D into Fusion you can change the FX parameter "Copies" to reduce it from 6 pod cavities down to 1. You can't increase the number from 6, or increase it again after reducing it, because that would involve editing all the timeline features one by one to include the shapes in the extra sections, it can be done but it's a bit laborious so choose a number and print it but don't save the file again because if you want a bigger one later you'll have to download it again.
I can create and supply an F3D with more slots if there's a demand, but you could just make it modular and print ones up to 6 and then use double-sided sticky tape to join them into the group you want.
PRINTING - I used PLA+ with 0.2mm layers, 0.4mm nozzle, infill 25% lines but not critical, everything else normal settings apart from a 2-line 0.7mm-spaced brim so it doesn't stick to the print, just for a clean nozzle.
ASSEMBLY - You don't really need 2 magnets per pod, one may be sufficient especially if they're N42 neodymium which are readily available and fairly cheap. The pips in the base locate in the holes in the main section to produce a neat finish. Add just a dab of glue if it doesn't hold together on its own. The holes under the magnets are just in case you want to remove the magnets from the model later for any reason. Without holes, you'd have to dig them out which could chip or break them, but poke a cocktail stick or other prodder through the hole and the magnet will pop out.
I wanted the magnets fully captive within the holder because if you put the holder down on a metal surface like a monitor stand then it will attach there without the magnets gradually getting pulled out. Pullout could happen if they're just placed in the bottom face of the holder. Original design had little tabs there in the hope of holding them in place, but PLA creeps under constant load so I would expect them to pull out anyway over time, especially as the little tabs get broken off when putting the magnets in :o)
HARDWARE - 1 or 2 magnets per pod, using 10x5x2mm N42. In the UK these are readily available on Amazon, some of which are from First4Magnets.com If you're only buying one pack then they may be cheaper on Amazon, but if you're wanting more than one it may be cheaper to buy direct from First4Magnets which has been a super company to deal with in my experience, packaging is always very good and the Royal Mail 2-3 day service is fine. Other brands might be fractionally different size, F4M ones are absolutely bang on 10x5x2. Don't pinch your skin between magnets, THEY BITE!
Please Like this model if you find it useful.
If you REALLY like it, https://www.buymeacoffee.com/gigabeast :o)
If you want a custom size, just ask. If I can do it I'll let you know. I'll probably want a coffee first though!