1 / 10
BNO085 IMU Snap-Fit Mount (Adafruit 9-DoF breakout, STEMMA QT) — zdjęcie 1
1 / 10

BNO085 IMU Snap-Fit Mount (Adafruit 9-DoF breakout, STEMMA QT)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

PETG snap-fit mount for the Adafruit BNO085 IMU: 30×50 mm plate with heat-set posts, cover with STEMMA QT windows

Ocena
0 / 5
Polubienia
1
Pobrania
10
Wydruki
0
Wyświetlenia
34
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Share Alike

Snap-fit mount for the Adafruit BNO085 9-DoF IMU breakout (product 4754).

Buy the board: https://www.adafruit.com/product/4754

A PETG base plate and a snap-on cover. The board screws into brass heat-set inserts, and the cover snaps on with two keyed tabs so it only fits one way. Windows at both ends give access to the STEMMA QT / Qwiic (JST SH) connectors. A raised +X/+Y arrow on the plate and V-groove arrows on the cover mark the sensor axes.

SIZE (mm)

- Plate: 30 x 50 x 4 mm, with board posts reaching 9 mm

- Cover: 30 x 27.46 x 16.1 mm; the 16.1 includes the snap hooks that reach down into the plate

- Assembled height: 16.4 mm

MOUNTING

- 4 holes in a 20 mm (X) x 40 mm (Y) centre-to-centre pattern

- One hole is a 3.2 x 3.8 mm slot to allow for misalignment; the others are 3.1 mm (tight) and 3.4 mm

- Fasten with M3 x 12 button-head screws into M3 heat-set inserts (5.7 mm long, 4.6 mm OD) in the part you are mounting to (4.2 mm bore, about 11 mm deep)

- The board insert pockets are 3.4 mm diameter x 5 mm deep, on a 20.32 x 17.78 mm pattern (the BNO085 hole pattern), with a 2.2 mm drain hole

HARDWARE (per mount)

- 4x M2.5 brass heat-set inserts, 3.5 mm OD x 4 mm long (HANGLIFE or similar): https://www.amazon.com/dp/B0CS6YVJYD?tag=phrintables-20

- 4x M2.5 x 6 button-head screws (ISO 7380), board to inserts: https://www.amazon.com/dp/B09HQL6T2P?tag=phrintables-20

- 4x M3 x 12 button-head screws (ISO 7380), plate to the mating part: https://www.amazon.com/dp/B07H194XLQ?tag=phrintables-20

- 4x M3 heat-set inserts (M3 x 5.7 x 4.6 mm) in the mating part: https://www.amazon.com/dp/B0BVMMBG2N?tag=phrintables-20

- No spacers. The cover needs no screws.

PRINTING

- PETG, 4 perimeters, 4 top and bottom layers, 20% gyroid infill

- Plate: print flat on its bottom. Cover: print upside down on its roof.

- No supports

The SCAD source is included. The drawings are not to scale; the dimensions govern.

As an Amazon Associate I earn from qualifying purchases. The Amazon hardware links above are affiliate links; the Adafruit link is not.

Tagi