1 / 4
Christmas Village – LED Tealight Houses — zdjęcie 1
1 / 4

Christmas Village – LED Tealight Houses

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Four snowy houses that glow with an LED tea light. Multicolour 3MF for the INDX (or MMU3), no supports.

Ocena
0 / 5
Polubienia
4
Pobrania
42
Wydruki
1
Wyświetlenia
132
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

A small Christmas village that lights up from the inside. Drop a standard LED tea light into each house, put the roof back on, and the windows glow warm in the dark. Four houses that belong together, plus two fir trees to fill the gaps.

The houses

  • Half-timbered house (68 × 67 × 97 mm): pink plaster, grey timber frame, an upper floor that juts out on brackets, beaver-tail tiles, brick chimney, wreath on the door

  • Stone cottage (66 × 82 × 75 mm): rubble walls with corner quoins, green board shutters, stone door arch, flat red tiles, stone chimney

  • Swedish house (66 × 77 × 78 mm): Falu-red board-and-batten walls, white corner boards and window frames, grey slates

  • Chapel (60 × 84 × 110 mm): stone nave with buttresses and lancet windows, bell tower with twin openings, slate spire and cross

  • Two fir trees (51 and 73 mm) on snowy bases

How it works

  • Every house stands on its own snowy base, which is also the floor

  • A ring in the floor centres any Ø 38 × 16 mm LED tea light; a Ø 16 mm hole underneath lets you push it out or reach its switch

  • The roof lifts off. Two rails under it slide inside the walls with 0.3 mm clearance, so it sits square and cannot slide off

  • Snow lies on every roof, with a ragged edge where the tiles show through

  • The chimney plugs into the ridge; the chapel spire plugs into the tower

  • LED tea lights only, never a real candle

Print settings

  • PLA, 0.4 mm nozzle, 0.2 mm layers, 3 perimeters, 15 % infill

  • No supports and no brim. Bodies and roofs print upright, chimneys upside down, exactly as placed in the 3MF files

  • Slopes stay within 40° of vertical and no bridge is longer than 5 mm: window panes are under 4.6 mm wide, doors and the chapel windows have pointed or sloped tops, and protruding details have bevelled undersides (only sub-millimetre ledges remain)

  • One house is about 4 h in one colour (body about 2 h, roof about 1 h 40). Weights: 35 to 40 g per body, 21 to 27 g per roof. Times are estimates, check them in your slicer

  • Thin white or pink PLA lets a little light through the walls, which looks lovely at night

Colours: made for the INDX, MMU3 works too

  • Designed with the Prusa Core One INDX tool changer in mind: every colour has its own tool, so the hundreds of colour changes on the timber and board walls take seconds each, with far less purge waste than a single-nozzle filament changer

  • The 3MF files open with the Core One INDX profile: tool 1 red, tool 2 white, tool 3 grey, tool 4 green, tool 5 pink. Everything fits a 4-tool INDX except the half-timbered body, which uses all five colours (8-tool profile). With 4 tools, move its small red detail by the door to the pink or white tool

  • MMU3: switch the printer profile to Core One + MMU3 and load the same colours in slots 1 to 5. It works the same, just slower, with a wipe tower

  • Colours are stacked by height wherever possible to keep filament changes low: the snowy base is white, the roofs are tiles below the snow line and white above it

  • Chapel: about 76 colour changes for the body, 25 for the roof, 3 for the spire. Stone cottage: about 98 and 23. Swedish house: about 228 and 19. Half-timbered house: about 272 and 25 (the grey timber runs over most of its height)

  • Fir trees: green, grey trunk and white base, 4 to 6 changes

  • One colour: use the STL files; white or grey looks great once lit

  • File names are in French: corps = body, toit = roof (+ chimney or spire), cheminee = chimney, fleche = spire, sapin = fir tree, alsacienne = half-timbered, chaumiere = stone cottage, suedoise = Swedish, chapelle = chapel

Make it yours

The whole village comes from a parametric Python script (manifold3d, gen.py and its modules): sizes, roof pitch, tile style, snow line, windows, shutters and wreaths. The script checks that each part is one piece, that nothing overhangs past 40° apart from sub-millimetre ledges, that every bridge is under 5 mm, that the tea light fits and touches nothing, and that each roof, chimney and spire seats with its clearance.

Designed with AI assistance (parametric Python script).

En français

Un petit village de Noël qui s'allume de l'intérieur : une bougie LED chauffe-plat dans chaque maison, le toit reposé par-dessus, et les fenêtres brillent dans le noir. Quatre maisons qui vont ensemble et deux sapins.

  • Maison à colombages (68 × 67 × 97 mm) : enduit rose, colombages gris, étage en encorbellement, tuiles en écaille, cheminée en briques, couronne sur la porte

  • Chaumière en pierre (66 × 82 × 75 mm) : moellons et chaînes d'angle, volets verts, arc de porte en pierre, tuiles plates

  • Maison suédoise (66 × 77 × 78 mm) : bardage rouge de Falun, planches d'angle et fenêtres blanches, ardoises grises

  • Chapelle (60 × 84 × 110 mm) : nef à contreforts et baies en arc brisé, clocher-porche, flèche en ardoises et croix

  • Deux sapins (51 et 73 mm) sur socle enneigé

Le socle de neige sert de plancher ; un anneau centre une bougie LED Ø 38 × 16 mm et un trou de Ø 16 dessous permet de la pousser ou d'atteindre l'interrupteur. Le toit s'enlève : deux rails glissent dans les murs avec 0,3 mm de jeu. La cheminée se plante dans le faîtage, la flèche dans le clocher.

Impression : PLA, buse 0,4, couches de 0,2, 3 périmètres, 15 % de remplissage, sans support ni bordure. Corps et toits debout, cheminées tête en bas, comme dans les 3MF. Pentes à 40° de la verticale au plus, aucun pont de plus de 5 mm (carreaux de moins de 4,6 mm, portes et baies en pointe ou biseautées). Environ 4 h par maison en une couleur (estimation).

Couleurs : pensé pour l’INDX de la Core One, un outil par couleur, donc des changements rapides et beaucoup moins de purge. Les 3MF s’ouvrent avec le profil Core One INDX : T1 rouge, T2 blanc, T3 gris, T4 vert, T5 rose. Tout passe sur un INDX à 4 outils sauf le corps à colombages (5 couleurs : avec 4 outils, passer son petit détail rouge sur le rose ou le blanc). Le MMU3 marche aussi, mêmes couleurs dans les emplacements 1 à 5, avec une tour de purge. Couleurs empilées par hauteur pour limiter les changements (chapelle ≈ 76 + 25, chaumière ≈ 98 + 23, suédoise ≈ 228 + 19, colombages ≈ 272 + 25). Une couleur : fichiers STL.

Bougies LED uniquement, jamais de vraie bougie.

Tagi