1 / 1
Lego Technic Pin Pusher – Double-Ended Pin Removal Tool — zdjęcie 1

Lego Technic Pin Pusher – Double-Ended Pin Removal Tool

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A small double-ended tool for pushing stuck Technic pins out of beams: a short end for one beam, a long end for 2.

Ocena
0 / 5
Polubienia
0
Pobrania
3
Wydruki
0
Wyświetlenia
18
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Building Toys
Licencja
Creative Commons — Attribution

Friction pins (the black and blue ones) can sit really tight, and pulling them out by the collar with your fingernails or pliers often scratches the parts. It's much easier to PUSH a pin out from the other side. That's what this tool is for.

TWO ENDS, TWO JOBS

• End "1" (9 mm): pushes a pin out of a single beam. It's short and stiff, so use it for most jobs.

• End "2" (17 mm): pushes a pin through two stacked beams when you can't pull the beams apart first.

Tip: if a pin joins two beams, pull the beams apart first. The pin stays in one of them and comes out much easier with end "1".

FOUR ROD SIZES

The diameter is engraved on the handle. All four fit standard Technic holes, so pick whichever you like, or print them all. A set of four takes about the same print time as one.

• pusher_3.9 – Ø 3.9 mm, thinnest, easiest to get into the hole

• pusher_4.2 – Ø 4.2 mm, middle size

• pusher_4.5 – Ø 4.5 mm, most contact with the end of the pin, strongest

• pusher_3.9-4.5 – tapered 3.9 → 4.5 mm, self-centering tip, thicker at the base where rods usually break

A Technic hole is about 4.8 mm and the hole through a pin is about 3.2 mm. The rod is sized so it goes into the beam's hole and pushes on the rim of the pin, without slipping inside the pin.

DESIGN NOTES

• The rods are meant to be printed lying flat. That way the layers run along the rod. A rod printed standing up breaks at a layer line the first time you push at an angle.

• The bottom of each rod is cut flat by 0.3 mm so it sits on the bed without supports.

• A cone at the root of each rod spreads the load. The sharp corner between rod and handle is where these tools usually snap.

• The tip has only a tiny 0.2 mm chamfer, so the flat face still has enough area to push on the pin.

PRINT SETTINGS

• Material: PETG (recommended). It's tough and flexes a little before it breaks, which suits a thin rod. PLA / PLA+ works too, but it's more brittle: don't lever with it, push straight. Nylon (PA) is the toughest option if you have it and can dry it. It's overkill for this tool.

• Orientation: as in the file, lying flat. No supports.

• Layer height: 0.16–0.2 mm

• Walls: 4–5 perimeters. That makes the rods solid, so infill doesn't matter for them.

• Infill: 30–40% for the handle

• Optional: a quick pass with P400 or finer sandpaper takes off the seam on the side of the rod. Don't sand the flat tip.

HOW TO USE

1. Put the rod into the hole on the side where the pin is flush with the beam.

2. Hold the beam firmly and push straight along the hole axis. Don't lever sideways.

3. For a 3L pin, push from the short side.

SOURCE

The OpenSCAD source (pin_pusher.scad) is included. Rod diameters, lengths and handle size are parameters at the top of the file. Set only = 0..3 to export a single variant, or -1 for all of them on one plate.

LEGO® and Technic™ are trademarks of the LEGO Group, which does not sponsor, authorize or endorse this model.

Tagi