1 / 6
CORE One Pins Mod 5G — zdjęcie 1
1 / 6

CORE One Pins Mod 5G

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

The ultimate 🚀 motion system upgrade for the XY gantry of the CORE One 🥰: 5mm steel axles and genuine Gates idlers 😎.

Ocena
5 / 5
Polubienia
92
Pobrania
302
Wydruki
3
Wyświetlenia
1924
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Open Community License v1.1

The 🥰 CORE One is an excellent printer with a well-designed stock system, but the Pins Mod offers mechanical improvements for enthusiasts seeking enhanced precision and reliability. Inspired by the VORON community, it upgrades the XY gantry system by replacing the standard M3 bolts used for idler mounting with 5mm steel axles (pins) and genuine Gates idlers.

What's the new with 5G:

While the original Pins Mod replaces the M3 bolts with 3mm pins, keeping the stock Prusa idlers and requiring only minimal changes to the printed parts, this Pins Mod 5G leaves this comfort zone: Parts are beefed-up and optimized to use 5mm axles and genuine Gates idlers, of course while keeping full compatibility to other stock parts of your printer.

Key Improvements

  • Eliminated Idler Play on the M3 bolts

  • Enhanced Durability by using genuine Gates Idlers for 5mm shafts

  • Smoother Operation that reduces vibration and mechanical noise

  • Corrected Gen2 Motor Pulley Clearance: Restores the original GT2-style pulley clearance to prevent rubbing on the stock motor mount parts

  • Toothed Idler Integration: Optimizes belt engagement using purpose-built toothed idlers; reposition the idler to account for the different pitch-circle diameter and keep the belt path parallel

  • Improved Reliability for the Belt Tensioner mechanism by using a heat set insert (optional)


CORE One L Companion Parts

The XY Motor Mounts for the Core One L require slightly different parts. Find these adapted mounts in the companion model: Core One L Pins Mod 5G. All other parts and instructions are exactly the same, just print those two replacement parts.

Question and Answers

There is the Pins Mod already - why this 5G variant? 🤔

The 3mm Pins Mod works great - full stop - and it still has it's place: It reuses the stock idlers and requires only a minimal BOM. But me (and others) have experienced quality and durability issues with the stock Prusa idlers, with bearings failing right from the start or within the first year of use. 

So the route was set for the Pins Mod 5G, using 5 mm pins and high quality, precision, genuine G ates idlers which should last about the lifetime of the printer in this setup.

GT 1.5 and the Gen 2 Upgrade: Do I still need this mod? 🤔

Yes 😎 and with the GT 1.5 / Gen 2 belt change, the Pins Mod (5G) is even more valuable. The GT 1.5 / Gen 2 upgrade improves the belt system, but it does not eliminate the radial play introduced by the stock M3 idler mounting bolts. The Pins Mod addresses that remaining weakness by replacing the bolts with precision steel pins, making the idler assembly more rigid, smoother, and more consistent.

In addition, there is a Gen2-specific fix: The new motor pulleys included in the Gen2 upgrade kit have a slightly larger outer diameter and can rub on the stock Motor Mount printed parts. This is corrected by restoring the same pulley clearance that was present with the GT2 pulleys.

Assembly

The assembly steps are very similar to original Pins Mod (with 3mm pins) but due to the larger diameter pins much easier and safe.

General Assembly Rules

  • The holes in the printed parts are intentionally undersized. Follow the instructions below to get a perfect fit for the 5mm pins, independently of your slicer settings.

  • ⚠ Critical: Never force-push pins through bearings - any stress on the inner bearing race can cause permanent damage; if required, slightly sand down the pin so that the idler can slide onto it without any force.

  • Avoid any load on the bearing shells and printed parts during assembly. Use the provided spacers tools to keep the load away from the bearing (but rather on the flange of the idler) and also to prevent the printed part from bending.

  • All holes for the 5mm pins are going through the complete part. This allows you to:

    • Easily prepare the holes from both sides of the part

    • Use a 5mm pin punch (or a slightly undersized 5mm pin / shaft / bolt) to align the idler from one side while pressing in the pin from the opposite site

Pin Preparation

Initial Preparation

  1. Ensure pins have a slight chamfer on both ends

  2. Test-fit each pin through idler bearings completely

Sizing Process (if pins are oversized)

  1. Secure pin in cordless drill chuck

  2. Use 180-grit sandpaper to uniformly reduce diameter

  3. Rotate drill while applying light, even pressure with sandpaper

  4. Work the entire shaft length for consistent sizing

  5. Reverse the pin the the drill and repeat the steps on the now accessible areas

  6. Clean pin thoroughly and retest bearing fit

  7. Repeat process until pin slides freely through bearings

    • Typical sizing time: 30 seconds per pin

Quality Check: Final pins should insert smoothly into bearings with no resistance or binding

Printed Parts - Hole Sizing

Tip: The process is really easy, but print yourself some spare parts and test what works best for you!

The 5mm pins are designed to be press-fitted into the printed parts. To ensure a secure fit without cracking the rigid PC-CF part, aim for a measured hole diameter of 4.95mm. On a well-tuned printer, this fit should be nearly perfect right off the build plate, though holes are intentionally slightly undersized.

To efficiently and reliably get the perfect fit, here is what you can do:

  • Required tools:

    • 5.0mm drill bit

    • 4.9mm drill bit (if you do not have one, it's more than worth spending those 5 bucks!)

    • One of the pins you prepared in the previous step

  1. With the 4.9mm drill bit and using a cordless drill: Clean up the holes 

  2. Take the 5.0mm drill bit and just by hand: Carefully "screw" the bit slightly into the hole on one side

  3. ... and optionally, repeat the same for the opposite side (see Pro Tip below)

  4. Test-fit the resulting hole size with the pin.

This should give you a perfectly tight fit to securely hold the pin, while still allowing to easily insert the pin and aligning the idlers without any risk of breaking the part.

Pro Tip

For the most perfect secure fit while still stress-free to assemble:

  • Check from what side you want to press in the pin

    • Belt Tensioner: take either side

    • XY Carriage and Motor Mount: press in from the thinner side

  • Hand drill only this side with the 5mm drill bit (step 2)

  • ... and skip step 3 and leave the opposite side drilled with 4.9mm only (in step 1)

This will allow you to still easily insert the pin and align the idlers without using too much pressing force - no risk of damaging the parts or the bearing - while still holding the pin extremely secured when fully pressed in.

Printed Parts - Heat Set Insert

Make sure the heat set Insert is fully seated in the part!

Pin Insertion and Spacer Usage

  • Use a parallel-press tool or vice for fully seating the pin.

  • A 5mm pin punch (or a sanded down / undersized pin) is perfect for aligning the idler from the opposite side.

  • Spacers will keep any load from the part and the bearing shells.

Installation of idlers in other parts follows the same concept.

For the Idler Stack in the Motor Mounts:

  • Pres in the pin in multiple steps

  • Add first idler and shim; then align the second idler with the pin punch.

  • Finally add the spacers and fully seat the pin with the parallel press tool.

  • Note: The 30mm pin will not be flush with the outer surface of the part, but will be recessed by 1mm.

Parts Details

Front Tensioner

  • Pin 18mm: 1 pcs.

  • Idler 2GT 20T Smooth: 1 pcs.

  • Optional: M3x5x4 Heat Set Insert (Voron Spec): 1 pcs.

XY Carriage

  • Pin 28mm: 2 pcs.

  • Idler 2GT 20T Smooth: 1 pcs.

  • Idler 1.5GT 27T - Toothed: 1 pcs.

Motor Mount Left

  • Pin 30mm: 2 pcs.

  • Idler 2GT 20T Smooth: 3 pcs.

  • Spacer ID5, OD 7mm, L 1mm: 1 pcs.

Motor Mount Right

  • Pin 20mm: 1 pcs.

  • Pin 30mm: 1 pcs.

  • Idler 2GT 20T Smooth: 3 pcs.

  • Spacer ID5, OD 7mm, L 1mm: 1 pcs.

Quality Checks

Verify that the pins are flush with (or below) the outer surface.

Confirm idlers rotate freely without binding. Check for proper alignment and smooth operation.

Make sure the layers haven't separated. There should be no visible stress marks on the printed parts.

Print Settings


Seam Placement

Make sure the slicer does not position the seam close to the idlers.  The picture shows the region to avoid for the Belt Tensioner, do the same for all the printed parts.

Recommended print settings:

  • Filament: PC-CF

  • Layer Height: 0.2mm

  • Infill: 40%

  • Perimeters: 4

  • Top/Bottom Layers: 5

  • Support: No

BOM

  •  5mm Steel a Pins:

    • 18mm: 2 pcs.

    • 20mm: 1 pcs.

    • 28mm: 4 pcs.

    • 30mm: 3 pcs.

  • "Genuine" Gates Idler produced/distributed by 3DO,  E3D, KB3D, Fliastruder, YouPrintin3d and others:

    • Idler 2GT 20T - Smooth (Bore/ID 5mm), for 6mm belts: 10 pcs.

    • Idler 1.5GT 27T - Toothed (Bore/ID 5mm), for 6mm belts: 2 pcs.

    • Alternative Source:

      • Mellow idlers have the exact same dimensions: Mellow LL-1.5GT
        (Make sure to select the correct configuration)

      • ⚠ POWGE idlers have larger outer flange diameter and do not fit!

  • Spacer for the idler stack in the Motor Mount:

    • ID5, OD 7mm, L 1mm: 2 pcs.
      (Mizumi Catalog Item  CIMRS5-7-1 or any 5x7x1.0mm Alu Shim as used for RC models e.g. XRAY Alu Shim 5x7x1.0mm

  • Heat Set Insert (Optional):

    • M3x5x4 Heat Set Insert (Voron Spec): 2 pcs.

Tagi