Monitor Handle for Ergotron HX Arm – VESA 100, MSI MPG 491CQP
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Grab handle for moving a big monitor on an Ergotron HX arm.Bolts under the two bottom VESA 100 screws. Fit test included
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 16
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
UPDATE: v2 is out – two grips in front of the screen's bottom edge instead of a bar hidden under it, and loose cables instead of the clip
A grab handle for positioning a heavy monitor on a spring arm. It bolts on under the two bottom VESA screws, runs down the back of the monitor and ends in a 28 mm bar right behind the bottom edge of the screen. From your chair you don't see it, but your hand finds it without looking. A C-clip on the back holds the cable bundle.
I made it for my MSI MPG 491CQP QD-OLED (49" curved, 8 kg) on an Ergotron HX desk arm. Moving that monitor by the screen edges is awkward, and I couldn't find a ready-made handle.
WILL IT FIT YOUR SETUP?
Tested only on the MSI MPG 491CQP + Ergotron HX. Nothing in it is specific to MSI, so it should work with other VESA 100 monitors of a similar shape: a thick back that ends not far below the VESA mount, with only the thin screen panel continuing down in front. Check the points below. If you're not sure, print the fit test first (20 g, 1 h).
1. The VESA plate. The handle lies flat on the arm's VESA plate, right under the two bottom screws. The plate part is 118 × 30.5 mm and reaches from 8.5 mm below to 22 mm above the bottom screw centres. On the Ergotron HX plate there's a pressed rib (about 70 × 10 mm, about 6 mm tall) above the bottom screws – the handle has an 80 × 13 × 7.5 mm pocket for it. The top edge stops 1 mm below the HX quick-release bracket. A flat plate from another arm should work too, as long as nothing else sticks up in that area.
2. The back of the monitor. For the first 55 mm below the plate, the handle's arm runs 15 mm above the VESA plate surface. On the 491CQP the plate sits in a 7 mm deep recess with a raised strip below it that sticks out another 5 mm, which leaves 3 mm of clearance. Further down, the arm drops to the level of the VESA plate and passes under the bottom of the monitor's back. On the 491CQP the thick back ends 63 mm below the bottom VESA screws. So on your monitor: nothing more than about 12 mm above the plate surface in the first 55 mm below the plate, and nothing at the level of the plate or behind it more than 64 mm below the bottom screws.
3. Bar height. The centre of the bar is 122 mm below the bottom VESA screws. On the 491CQP the bottom edge of the screen is 117 mm below them, so the bar sits behind and just below the edge. Measure this distance on your monitor: much less and the bar sticks out further below the screen (still works); much more and the bar ends up higher behind the screen, harder to reach.
4. Buttons on the bottom. The bar hangs about 56 mm behind the back of the screen panel. On the 491CQP the joystick sits in the middle of the bottom edge and stays easy to reach from the front. Check where your buttons are.
5. Screw length. 7 mm of plastic plus a washer goes under each screw head. The M4×18 screws go about 10 mm into the monitor – the original screws went 9.5 mm, and the holes are 17.7 mm deep. For another monitor: new screw length = how deep your current screw goes in + about 8 mm, and it must not bottom out in the hole.
HARDWARE
- 2× M4×18 socket head cap screw (they replace the two bottom VESA screws; the top two stay).
- 2× M4 washer (DIN 125, 9 mm outside diameter).
INSTALLATION
1. Lower the monitor all the way and support it from below (a box or a few books).
2. Remove the two bottom VESA screws. For a moment the monitor hangs on the top two – that's fine.
3. Put the handle on, insert the M4×18 screws with washers and tighten firmly.
4. Open the cable strap near the clip and press the cables into the C-clip from the back, 2–3 at a time (opening 10.5 mm, inside 16 mm). No need to unplug anything.
5. After a week of use, tighten the screws once more.
PRINTING
- PETG. Not PLA: under constant screw pressure PLA slowly gives way and the screws loosen, and it can crack when you pull the handle hard. The back of the monitor also gets warm.
- Profile 0.20 mm STRUCTURAL (Prusa CORE One+, 0.4 nozzle). Saved in the 3MF: 6 perimeters, 6 top / 5 bottom layers, 40% cubic infill, 100% infill around the screws.
- Print flat, monitor side down, as in the file. Organic supports are painted only under the arm and in the pocket.
- About 223 g and 8 h 45 min. Make sure the spool has enough filament.
- Remove every bit of support from the pocket – there's only 1.5 mm of clearance above the rib on the plate.
FIT TEST
MonitorHandle_FitTest: the same monitor-facing shape as the handle (plate part with the pocket, screw seats and the first 35 mm of the arm). About 20 g, 1 h, PLA or PETG, 0.20 mm SPEED. It prints standing on its top edge, without supports. All settings are saved in the 3MF: 2 perimeters, Lightning infill, solid around the screws, 3 mm brim.
Screw it on and check:
- It lies flat on the VESA plate and both screws go in without rocking.
- It doesn't touch the arm's bracket or the edges of the recess.
- The arm doesn't rub on the back of the monitor (slide a sheet of paper between them).
- Tilt the monitor fully both ways – nothing catches.
- A hex key reaches both screws.
Fan-made accessory, not affiliated with or endorsed by MSI or Ergotron. The product names are used only to say what it fits.