Portable 130mm(F4) Newtonian telescope (IG130P_MK2)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is an improved version of the previously posted portable 130mm (f/4) Newtonian telescope.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 10
- Wydruki
- 0
- Wyświetlenia
- 88
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Physics & Astronomy
- Licencja
- Creative Commons — Attribution — Share Alike
Hello everyone,
I previously shared my 130P and 150P portable reflector telescope designs and have been continuously refining them through hands-on use.
This post features the updated design for the 130P model (IG130P_MK2). (The updated files for the 150P will be shared soon!)
While using them for astrophotography, I noticed several areas that could be enhanced, leading to the creation of this updated model. These improvements mainly focus on eliminating micro-vibrations for sharper long-exposure images, managing stray light, preventing dew, and optimizing cooling.
Additionally, I have attached the STEP files so you can easily modify the design or create custom accessories. Feel free to use them! :)
If you have any questions during the build process, don't hesitate to ask—I'll be happy to help.
The following improvements have been made, primarily to facilitate astrophotography. (For visual observation, the MK1 model remains more than sufficient.)
4-Vane Spider: Redesigned the UTA spider into a 4-vane orthogonal (cross) pattern to produce clean, classic cross-shaped diffraction spikes on bright stars.

Elevated Tube Band Base (Pier Clearance): Increased the height of the dovetail mounting base on the tube band to prevent physical interference between the telescope tube (LTA) and the mount/pier when targeting high-altitude or zenith objects.
Simplified Tube Band Clamping: Updated the tube band clamping mechanism to use standard M5 bolts and nuts, making it simpler to assemble, print, and use.

Shroud Guide: Guides have been added to the UTA (Upper Tube Assembly) and the main tube to allow for easy attachment of an EVA foam shroud.

Note: Please refer to the attached drawing to fabricate the shroud. Using 4T EVA foam is recommended.

Focuser Base Support: A support has been added to prevent the focuser from sagging under the weight of equipment such as cameras and coma correctors.

Secondary Mirror Dew Heater: A dew heater has been integrated into the secondary mirror assembly.
Upgraded 50mm Secondary Mirror: Upgraded the secondary mirror size from 40mm to 50mm. When shortening the truss tubes to achieve proper back-focus for accessories like coma correctors, this larger mirror effectively prevents optical vignetting and ensures full illumination across the sensor area.


Primary Mirror Cooling Fan: A cooling fan has been installed behind the primary mirror.

Focuser Adapter: An adapter has been added to allow for the rotation of the focuser.

Secondary Mirror Dew Heater & Wiring:
The wiring for the secondary mirror dew heater runs along one of the spider vanes to an external USB-C (5V) port located on the front-right side of the UTA.
To prevent excessive heat and minimize load, four 47Ω carbon resistors are connected in parallel right behind the USB-C connector (resulting in an effective resistance of ~10Ω and distributing just ~0.125W across each resistor).
This steps down a standard 5V, 2W heater down to an optimal 5V, 0.5W operating output.
The wires are cleanly routed and embedded inside the UTA body and finished with masking tape for a neat look.
Hardware & Electronics Links
PI Film Dew Heater (OD35mmIxD10mm5V2W):
AliExpress Product Link
Waterproof USB Type-C Female Port (with Pre-soldered Wires):

(Below are photos showing the embedded wire routing inside the UTA and the 4-parallel 47Ω resistor assembly.)





