MPC One Anker 737 Mount

This is a mount for the Akai MPC One which allows you to attach an Anker 737 External Battery.

3MF Notes:
The file uses ABS. However, any filament should be fine as these parts will not be exposed to high heat or UV.

Parts Needed:
Anker 737 Power Bank - https://www.amazon.com/dp/B09VPHVT2Z
USB C PD - 12V Cable (MPC One+ and MPC One G2) - https://www.amazon.com/dp/B0B9FDZX7P
Thin Double Sided Tape - https://www.amazon.com/gp/product/B002VLA5SI/ref=ox_sc_act_image_1?smid=ATVPDKIKX0DER&psc=1

Assembly:
A. Install the Power Cord Mount

1. Rotate the MPC One so the rear panel is facing you.

2. Remove the screw located between the Kensington lock insert and the MIDI IN port.

3. Use this screw to attach the Power Cord Mount to the MPC One.

4. Remove the thumb screw securing the Power Adapter Restraint.

5. Insert the barrel end of the USB-C PD-to-12V cable into the Power Cord Mount.

6. Position the Power Adapter Restraint around the cable.

7. Use the thumb screw to secure the Power Adapter Restraint to the MPC One.

8. Loop the cable out of the way for the next steps.

9. Remove the screw nearest the Power button.

B. Install the Battery Holder and Route the Cable

1. Flip the MPC One over so the bottom is facing you.

2. Remove the three screws from the far side of the MPC One, where the Battery Holder will be mounted.

3. Position the Battery Holder in place.

4. Secure the Battery Holder using the three original screws. Be careful to follow the existing threads to avoid cross-threading or damaging the plastic.

5. Locate the USB-C end of the USB-C PD-to-12V cable.

6. Insert the USB-C end into the vertical hole in the Storage Compartment.

7. Starting from the rear of the MPC One, gently pull the cable slightly taut (there should be a small gap around the top of the power button) into the rear portion of the cable indentation. 

8. Carefully press the cable into the indentation, taking care not to damage it.

C. Secure the Battery Holder

1. Rotate the MPC One so the rear panel is facing you.

2. Reinstall the screw nearest the Power button to secure the Battery Holder in place.

D. Install the Power Bank and Storage Lid

1. Flip the MPC One over so the top is facing you.

2. Loop the cable inside the Storage Compartment so the USB-C connector faces the Battery Compartment.

3. Insert the Anker 737 Power Bank into the Battery Compartment, with its USB ports facing the Storage Compartment and its display facing upward.

4. Connect the USB-C PD-to-12V cable to the Anker 737 Power Bank.

5. Insert the Storage Lid into the top of the Storage Compartment, ensuring the hinge posts snap securely into the hinge tabs.

E. Install the Battery Cover

1. Apply double-sided tape to the inside of the Battery Cover along the top, bottom, and sides of the display opening.

2. Position the Battery Cover with its flat side facing up, aligning the display opening with the display on the Anker 737 Power Bank.

3. The Battery Cover is designed to fit by friction. Carefully press along the edges until the cover sits flush.

4. Apply light pressure around the display opening to ensure the tape adheres securely to both the Battery Cover and the Power Bank.

F. Power On and Play

1. Plug the power cable into the MPC One.

2. Power on the MPC One.

3. Make music!

Known Compatible Models:
Akai MPC One G2
Akai MPC One Plus

Version History:
V1.0 - 2026-10-28 - Initial release.
V1.1 - 2026-10-29 - Adjusted sizing to sit more flush with front of MPC.