1 / 5
Fingerboard + Skatepark - Rideable Finger Skateboard with Ramps, Rails & Stairs, No Screws — zdjęcie 1
1 / 5

Fingerboard + Skatepark - Rideable Finger Skateboard with Ramps, Rails & Stairs, No Screws

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A rideable fingerboard with printed trucks, wheels and a deck press, plus a 6-obstacle mini skatepark.

Ocena
0 / 5
Polubienia
0
Pobrania
3
Wydruki
0
Wyświetlenia
27
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

A complete finger skate set you print yourself: a full-size fingerboard that really rolls, ollies and grinds, plus a 6-obstacle mini skatepark to ride it on. No screws, bearings, glue or metal parts.

THE BOARD

  • A 97 x 29 mm deck with real concave and 22-degree kicktails, and a retro sunset graphic engraved underneath

  • Shape it like a real deck with the included printed deck press (heat and press). A pre-shaped version for printing with supports is also included

  • Trucks held on by 8 bolt-style printed pins, 10 mm wheels spinning freely on 3 mm printed axles

  • v2 hardware is bigger and looser, made to print reliably on any FDM printer

THE PARK

  • 2 quarter pipes with coping (face to face = mini half-pipe)

  • A kicker ramp

  • A funbox with a grind ledge and manual pad

  • A 3-step stair set with a handrail

  • A flat grind rail with feet

PRINT SETTINGS

  • The 3MF is ready to print with 5 plates, 0.4 mm nozzle, no supports (except the optional pre-shaped deck)

  • Board parts (deck, trucks, wheels, pins, caps): 0.12 mm layers, 100% infill, 4 walls (already set). The deck is 1.9 mm thick: PETG is best (springy), PLA works

  • Deck press: any colour, PLA is fine, 15% infill

  • Skatepark obstacles: 0.2 mm layers, 3 walls, 10% infill, printed upright as they are (rails lie on their side)

  • Plate 5 is optional: the pre-shaped deck with tree supports under the kicks, instead of the flat deck + press

  • About 5 g for the board, about 200 g for the whole park, about 35 g for the press

SHAPING THE DECK

  1. Heat water: about 85-90 C for a PETG deck, about 70 C for PLA.

  2. Dip the flat deck (tongs!) for 20-40 s until it is floppy. Keep the press out of the water.

  3. Lay it on the bottom press, graphic side down; the two small pins go up through the inner truck holes.

  4. Put the top press on (4 posts through its corner holes), push down firmly and hold 30-60 s until it cools.

ASSEMBLY

  1. Put a truck under the deck, kingpin nut facing the middle. Push 4 bolt pins down through the deck into the truck. Do both trucks.

  2. Slide an axle pin through a wheel (recessed side in), through the hanger, add the second wheel and press an axle cap on. The wheels spin freely with a little side play.

  3. Park: push the handrail pegs into the stairs, press the flat rail into its two feet, and arrange the obstacles however you like.

TIPS

  • Ride on a mouse pad or desk mat for grip

  • Wheels tight? Run a 4 mm drill bit through the bore by hand

  • Bolt pins or caps too tight or loose? Print just those at 97% or 103%

Original design by Kirimas Studio.

Tagi