1 / 3
Paper Towel Roll Dispenser - Removable Lid and Core V1 — zdjęcie 1
1 / 3

Paper Towel Roll Dispenser - Removable Lid and Core V1

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Three-piece kitchen roll dispenser with removable lid and hollow core. STL + editable STEP. Check roll dimensions.

Ocena
0 / 5
Polubienia
1
Pobrania
3
Wydruki
0
Wyświetlenia
19
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Kitchen
Licencja
Creative Commons — Attribution

A freestanding kitchen paper towel dispenser with a removable slip-on lid and a separate hollow core. Load a compatible roll, feed its free end through the side opening and replace the lid. All three parts are printable; no screws, magnets or other hardware are needed. The core can be replaced or edited separately.

DIMENSIONS AND ROLL FIT

Assembled: maximum diameter 121.8 mm x 231 mm high.

Body: diameter 116.8 x 228 mm; inside diameter 112 mm; wall 2.4 mm.

Core: diameter 42 x 221 mm; bore 38.2 mm.

Lid: maximum diameter 121.8 x 13 mm. Nominal slip-fit clearance is 0.4 mm per side.

The original reference roll was about 105.17 mm in diameter, with a 44.55 mm cardboard opening and 220 mm height. These are design reference dimensions, not newly measured dimensions of the pictured roll. The outlet is 10 mm wide and 210 mm high, so a 220 mm sheet cannot exit completely straight over its full height. The owner reports clean paper withdrawal with the lid fitted on their printed V1 and roll. Measure your roll and check feeding; compatibility with every paper roll is not established.

PRINTING AND ASSEMBLY

Recommended starting point: PLA or PLA+, 0.4 mm nozzle, 0.2 mm layers, 3 walls, 15% infill, 4 top and 4 bottom layers. Print at 100% scale in millimetres. Body and core upright on their flat bottoms; lid flat closed face down, in its exported orientation. Invert the lid for assembly. The original recommendation is supports off; check your slicer preview, especially the top of the outlet. Seat the core on the internal pilot, load the roll and fit the lid without forcing the parts.

ESTIMATES

Approximately 370 g PLA and 13 h 30 min for the complete set; about 148 CZK at 400 CZK/kg. These are analytical estimates, not slicer or measured print results. Your printer and settings will change them.

FILES

Three STL files and three editable solid STEP files, one per part, plus the English printing and assembly guide. STL and STEP are alternative formats of the same parts. STEP files are solid B-rep models, without a parametric feature history. No 3MF profile or G-code is included.

TESTING AND PHOTOS

The owner confirmed on 29 October 2026 that the pictured print was made from the supplied V1 files and paper feeds with the lid fitted without crumpling or tearing. This is an owner-reported functional check, not an independent test. The owner states the photographs show the actual print with AI-edited backgrounds. Printer-specific settings, measured fit and long-term durability have not been documented.

Software checks: all three STL meshes are closed, connected and manifold with consistent winding; all three STEP solids are valid; nominal assembled CAD parts do not overlap.

ORIGIN AND LICENSE

Original AI-assisted CAD design by Tomatoueu; not a downloaded third-party remix. Creative Commons Attribution 4.0 International (CC BY 4.0). Suggested credit: Paper Towel Roll Dispenser V1 by Tomatoueu, AI-assisted design, CC BY 4.0.

Tagi