1 / 8
Semi Truck Kit - Classic Long-Nose Tractor with Working Steering, Tilting Hood & 10 Spinning Wheels — zdjęcie 1
1 / 8

Semi Truck Kit - Classic Long-Nose Tractor with Working Steering, Tilting Hood & 10 Spinning Wheels

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

1:32 long-nose semi truck kit: steering front axle, tilting hood, 10 spinning wheels. No supports, no glue.

Ocena
0 / 5
Polubienia
3
Pobrania
10
Wydruki
0
Wyświetlenia
37
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Vehicles
Licencja
Creative Commons — Attribution — Noncommercial

A classic American-style long-nose semi truck tractor you build yourself. An original design (no brand logos) at about 1:32 scale: 221 mm long, 84 mm wide and 126 mm tall to the tops of the exhaust stacks.

WORKING PARTS

  • Steering: the whole front axle turns on a pivot pin, about 25 degrees each way

  • The hood tilts forward on its hinges (up to 90 degrees) to show the engine and radiator

  • All 10 wheels spin: two front singles and four rear duals on a tandem axle

  • The fifth-wheel coupling plate rocks back and forth, ready for a trailer

DETAILS

  • A ladder frame with axle hangers, a walking-beam tandem, fuel-tank brackets and a chrome bumper

  • A long hood with fenders, chrome grille, round headlights and side louvres

  • An inline-six style engine with turbo, oil filter, valve cover and radiator

  • A cab with raked split windshield, sun visor, roof marker lamps, air cleaners and mirrors, plus a tall sleeper box

  • Twin chrome exhaust stacks with heat shields, chrome fuel tanks and a mudflap bar with tail lamps

  • Everything is printed: no glue, screws, springs or metal axles. Parts plug together with printed pins and pegs

  • v1.1: the tandem rear axles are 39.5 mm apart, so the rear tyres no longer touch

PRINT SETTINGS

  • The 3MF is ready to print with 4 plates: 0.2 mm layers for the big parts, 0.12 mm for wheels, pins and mirrors, 0.4 mm nozzle, 3 walls, gyroid infill, no supports

  • Cab, hood and engine: 10% infill. Axle rods, pins, wheel caps and mirrors: 100% infill (already set in the 3MF)

  • Plates are grouped by colour: frame and chassis parts (gold), hood and engine (gold), cab, tanks, stacks and mirrors (white), rims and pins (white) + tyres (swap to black or TPU)

  • Every STL is already oriented. The frame prints upside down (rail tops on the bed); use a brim only if your bed adhesion is weak

  • About 250 g of filament. Largest part: the frame, 219 x 52 mm, so you need a bed of 220 mm or more (A1 / 256 mm beds are fine)

ASSEMBLY

  1. Wheels: press each tyre onto its rim from the inner side until it stops against the rim lip.

  2. Rear axles: push an axle rod through a rear dual wheel (rim face out), through both frame hangers, add the second wheel and press a cap on each end. Do both rear axles.

  3. Front axle: push the steering pivot pin into the top of the front axle beam, slide an axle rod through the end bosses, add the front wheels and caps, then push the pin up into the front cross-member. The axle now steers.

  4. Bumper: slide its two sockets onto the front ends of the frame rails. Mudflap bar: onto the rear ends.

  5. Engine: put 4 mounting pins in the rail holes and press the engine on, radiator at the front.

  6. Hood: spread its front corners slightly and clip the two hinge lugs onto the hinge pegs at the front of the frame. Swing it down.

  7. Cab: put 4 mounting pins in the rail holes behind the hood and press the cab on.

  8. Fuel tanks, exhaust stacks and mirrors: press them onto their pegs.

  9. Fifth wheel: 2 mounting pins into the rail holes over the rear axles, press the base on, then clip the plate onto the base pegs. The plate rocks.

TIPS

  • Pin or peg too tight? Sand it lightly. Wheels stiff? Spin them a few times, or open the rim bore with a 4.6 mm drill bit by hand

  • The steering stops on its own at about 28 degrees, when the tyres touch the fenders

  • Paint the grille chrome, the headlights white, the windows black and the tail lamps red for extra realism

Original design by Kirimas Studio.

Tagi