1 / 11
CURL - Pangolin Desk Organizer with a Rolling Scale Shell (Print-in-Place Tambour, No Supports) — zdjęcie 1
1 / 11

CURL - Pangolin Desk Organizer with a Rolling Scale Shell (Print-in-Place Tambour, No Supports)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A sleeping pangolin desk organizer: push its scaled shell and it rolls away to reveal pen, earbud and jewellery trays.

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
6
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Office
Licencja
Creative Commons — Attribution — Noncommercial

Closed, CURL is a sculpture of a sleeping pangolin: its tail is wrapped around its side, its little head rests on its claws, and it is covered in overlapping scales.

Open, it's a full desk organizer. Push the ridge on its back with one finger and the armoured shell rolls over its rump and tucks itself away under the belly. Pull the front row and the shell rolls back and clicks shut.

INSIDE

  • A 140 mm pen trough

  • An earbud cup

  • A 6-cell jewellery grid for rings and small things

  • A deep cable and charger bay

HOW IT WORKS

  • The shell is a real tambour: 19 rows of scales joined by printed knuckle hinges with cone pins, printed flat as ONE print-in-place chain

  • Every row has small triangular runners that ride in a V-groove inside both side walls. The groove loops over the back, round the rump and forward under the tray

  • When closed, the front row clicks into a slightly narrower end of the groove, so the shell does not creep open

  • Nothing needs supports, glue, screws, springs or magnets

PRINT SETTINGS

  • The 3MF is ready to print with 5 plates: 0.2 mm layers, 0.4 mm nozzle, 3 walls, 15% gyroid infill, no supports

  • Plate 1 is the PROTOTYPE kit (test track + 5 scale rows, about 2 hours and 60 g): print it first with the same settings to check your printer's fit

  • Tambour (scale shell): print flat, scales up, as one print-in-place piece. Clean flat bed, NO brim, keep elephant foot compensation ON (0.1-0.15 mm). Hinge clearances are 0.4 mm

  • The base prints upright: the track grooves and tray ledges are 45-48 degree V-shapes, so no supports are needed

  • Colours as in the photos: base in white, shell, head, tray and tail in red. Matte sandstone/tan or charcoal also look great, with the tray in a contrasting colour

  • About 650 g of PLA. Size about 262 x 170 x 118 mm. Every part fits a 256 x 256 bed (Bambu A1/P1/X1 and similar)

  • The three biggest parts (base, chest and head, tambour) are included as single-part 3MF files: the same mesh as the STL, just a much smaller download. They open in any slicer

PROTOTYPE TEST (recommended)

  1. Print the prototype plate (T1 test track + T2 five scale rows).

  2. Free the 5 rows and bend every joint until it moves easily.

  3. Push the rows into the two grooves at the cut end of T1, scales facing out, the row without the finger ridge first.

  4. Slide the rows round the curve and back. They should run smoothly with a light push. If they bind, see TIPS before printing the big parts.

ASSEMBLY (about 5 minutes)

  1. Free the tambour: flex every hinge back and forth until all 18 joints move freely (scales outward).

  2. Tray: lower it into the base between the side walls. Its sloped lugs sit on the matching ledges.

  3. Tambour: with the chest not fitted yet, push the plain end (row without the finger ridge) into both groove mouths at the front top of the base, slide it back over the back, round the rump and under the tray, until the ridged row is at the front.

  4. Chest and head: push its 4 pegs into the 4 holes in the front of the side walls. It closes the groove ends.

  5. Tail: push its 2 pegs into the 2 holes low on the right side wall.

TIPS

  • Shell stiff in the test track? Lightly sand the runners, or print T2/03 at 99% in Y only (the width across the rows)

  • Rows too loose and rattling? Print T2/03 at 100.5% in Y

  • Shell won't stay closed? Print the base at 99.7% in Y for a slightly tighter detent

  • To take the tray out: remove the chest, slide the shell out of the front, then lift the tray out

Original design by Kirimas Studio.

Tagi