1 / 10
Gearbox (worm gear + planetary gears, 640:1 or 2560:1) (Редуктор (червячная передача+планетарные передачи, 640:1, либо 2560:1)) — zdjęcie 1
1 / 10

Gearbox (worm gear + planetary gears, 640:1 or 2560:1) (Редуктор (червячная передача+планетарные передачи, 640:1, либо 2560:1))

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Gearbox (worm gear + planetary gears, 640:1 or 2560:1) Редуктор (червячная передача+планетарные передачи, 640:1, либо 25

Ocena
0 / 5
Polubienia
1
Pobrania
6
Wydruki
0
Wyświetlenia
80
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

Attention!!! Since I printed the gears using ABS (printing with nylon is practically impossible with a 0.25 mm nozzle, and with a 0.4 mm nozzle, the gear teeth don't turn out as well), there is some shrinkage. There is a gap in the gears, which causes them to slip under heavy loads. The teeth are too small—a consequence of the push for compactness.

After fine-tuning the ABS filament and adjusting the parameters, I managed to completely eliminate the backlash in the gears—as it should be—by replacing the sun and planet gears. Now, if a jam occurs and the strip fails to feed through the hotend, either the nylon thread snaps or the strip itself (the finished filament) breaks. The torque generated by the 4-stage reduction gearbox, running on a 12V power supply, is extremely high.

Someone might find a gearbox like this useful, so I’m sharing the STEP files in case you’d like to edit them. I designed it for a machine that produces 3D printing filament from plastic bottles. I didn’t want to use an existing design, and I didn’t have a stepper motor on hand, so I built it using parts I had lying around at home (I’m always working on projects, so I have plenty of spare parts). The gearbox is based on a standard 12V motor—in my case, one salvaged from an HP printer that was just sitting around. A worm gear provides a 10:1 reduction, followed by four planetary gear stages, each with a 4:1 ratio, bringing the total reduction to 2560:1. You can remove one planetary stage and swap in a taller output sun gear (included in the files) to achieve a total gear ratio of 640:1. I’ve also included files for a modular (disassemblable) spool.

What you’ll need:

- 2x 6810 bearings (if you’re using the spool)

- 3x 608 bearings (2 for the worm gear assembly, 1 for the planetary gear output)

- 1x 604 bearing (for the worm gear housing)

- 3x16 mm self-tapping screws (6 mm head diameter; exact quantity not counted)

- 2.5х8 self-tapping screws (4.6 mm head diameter; exact quantity not counted)

- M4 screws to attach the worm gear assembly to the planetary mechanism (there is a 3 mm thick wall between them; a sample is included in the files)

- M4x8 screws and M4 nuts are required for assembling the planetary gear sets.

- An M8x16 bolt and matching nut (this serves as the output component—the bolt transmits the rotation, and the nut connects it to the spool, at least in my setup) I printed all the gears using ABS with a 0.25 mm nozzle, while the other parts were printed in PETG using a 0.4 mm nozzle. The wall between the worm gear assembly and the planetary gear assembly could be made thicker than 3 mm—there is a bit of extra vertical clearance for the gears—but you shouldn't increase it too much. This is because each sun gear rests against the next one, and the final gear presses against an M8 bolt, which transmits the final rotation to the output. If the wall between the gear assemblies is too thick, the M8 bolt might not have enough engagement. The spool mounts directly onto the gear assembly; rotation is transferred to the spool via a plate with a cutout for a nut, featuring M4 screws positioned around its circumference that fit into corresponding slots on the spool.

For the worm gear assembly, an M4 heat-set insert (threaded insert) is used on the output shaft to keep things compact. The worm gear is secured to the output shaft using an M4x30 screw, which passes through a 604 bearing (the bearing is inserted into the cover from the outside; the screw goes through it and then into the heat-set insert). I’ve included screenshots of the complete assembly so you can see how everything fits together.

Внимание!!! Так как я печатал шестерни из АБС (из нейлона при сопле 0.25 печатать практически не возможно, а при 0.4 зубчики шестерни выходят хуже), то идет усадка. Есть зазор в шестернях, при большой нагрузке, они у меня проскакивают. Слишком маленький зуб, результат стремления к компактности.

После подгонки филамента АБС и настройки параметров мне удалось полность убрать зазор в шестернях (как и должно быть), менял солнечные шестерни и сателлиты. Сейчас, даже если какой-то затык и лента не идет черз хтенд, то либо обрывает капроновую нитку, либо рвется сама лента (уже готовый филамент). Крутяший момент на 4х ступнчатом редукторе и 12 вольтах питания очень большой.

Возможно кому-то понадобиться подобный редуктор, выкладываю степ-файлы для возможности редактирования. Я его сделал для аппарата по производству филамента из бутылок. Не хотел брать готовую схему, также не было шагового двигателя, поэтому собирал из того, что находил дома (я постоянно что-то делаю, запчастей много). Редуктор собрал на базе обычного моторчика на 12 вольт (в моем случае от принтера ХП), он валялся без дела. Червячная передача понижает обороты на 10 (10:1), 4 планетарные передачи понижают общее число еще до 2560 (каждая 4:1). Можно убрать одну планетарную передачу и поставить выходную солнечную шестерню более высокую (есть в файлах), тогда общее передаточное число будет 640. Разборную катушку тоже приложил в файлах.

Что понадобится:

- 2 подшипника 6810 (если будете использовать катушку)

- 3 подшипника 608 (2 в червячный редуктор, 1 на выход планетарной передачи)

- 1 подшипник 604 (в корпус червячного редуктора)

- саморезы 3х16 (диаметр шляпки 6 мм, количество не считал)

- саморезы 2.5x8 (диаметр шляпки 4.6 мм, количество не считал)

- винты М4 для крепления червячного редуктора к планетарному механизму (между ними стенка 3мм, образец в файлах).

- болт М8х16 и гайка к нему (это выходной элемент, винт передает вращение, а посредством гайки оно идет на катушку - в моем случае).

-Винты М4х8 и гайки М4 для сборки планетарных передач.

Все шестерни печатал из АБС, соплом 0.25, остальные детали из Петг, соплом 0.4. Стенку между червячным редуктором и планетарным редуктором можно делать толще 3 мм, у шестерней есть небольшой запас по высоте, но сильно увеличивать не стоит, так как каждая солнечная шестерня упирается в следующую, а последняя упирается в болт М8, которые передает окончательное вращение на выход. Если будет толстая стенка между редукторами, то может не хватить зацепления болту М8. Катушка одевается на сам редуктор. Вращение на катушку передается через пластину с вырезом под гайку, по окружности вручены винты М4, которые входят в ответные пазы на катушке.

При сборке червячного редуктора, на выходном валу, использована вплавляемая гайка М4 (для компактности). Червячная шестерня крепится к выходному валу винтом М4х30, через подшипник 604 (он вставляется в крышку снаружи, в него вкручивается винт, а дальше во вплавляемую гайку). Сделал скриншоты общей сборки, чтобы было понятно что и куда идет.

Tagi