CoralOwl - Desk Owl Camera Case & Stand for Synaptics Coralboard SL
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Owl desk case for Coralboard SL: camera eye, vent eye, all ports open, 15 deg tilt stand, no supports needed.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 29
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Your Coralboard is a little edge-AI brain - so give it a face. CoralOwl turns the Synaptics Coralboard SL into a friendly desk companion: the right eye is the camera window, the left eye is an airflow / speaker grille and the chest feathers are vents. All edge connectors stay usable, nothing needs supports, and the whole thing is held together by the same 4 screws that hold the board.
Features
Camera-ready: 4 bosses inside the face for a common 25 x 24 mm camera board (21 x 12.5 mm hole pattern, e.g. the Arducam OV5647 mini module). The lens looks through the right eye, tilted 15 deg up - ideal for someone sitting at the desk.
All ports reachable - cut-outs taken from the official Coral reference CAD: USB-C (oval opening + oval pocket so normal cable overmolds plug in fully), USB-A, Qwiic, both buttons (pin holes - use a paperclip), microSD (push-push - use a fingernail or toothpick), I2S (JST 7-pin) and the 2-pin battery connector.
Passive cooling: floor vents right under the SoC, grille eye and feather vents create a bottom-to-top airflow.
Optional easel stand with a captive 1/4"-20 nut pocket, so the owl also fits on any camera tripod. Without the stand the case lies flat.
Parts (all print without supports, already oriented)
CoralOwl_Face_Lid - print face down. Ear tufts lie on the bed.
CoralOwl_Base - print bottom down.
CoralOwl_Easel_Stand (optional) - print foot down.
Recommended: PLA or PETG, 0.2 mm layers, 3 perimeters, 15-20 % infill. Two-colour look: face in orange/coral, base in white, stand in black or grey.
Hardware
4x M3 x 12 screws (case only) or 4x M3 x 16 (case + stand). Screws go in from the bottom, through the base and the board, and self-tap into the lid pillars (2.6 mm holes).
4x M2 x 5 self-tapping screws for the camera.
1x 1/4"-20 hex nut (optional, tripod mount) - press it into the hex pocket under the stand.
Assembly
Screw the camera into the face lid (ribbon connector pointing down, towards the beak).
Plug the camera ribbon into the Coralboard CSI connector (22-pin, 0.5 mm; 15-pin camera modules need a 22-to-15-pin cable).
Put the board into the base - the ports line up with the cut-outs.
Place the face lid on top - its lip keys into the base.
Turn it over and drive the 4 M3 screws from below (add the stand plate first if you use it).
Key dimensions
Case 79 x 64 x 22.5 mm (without ears). Wall 2.4 mm, 0.6 mm clearance around the PCB, 4.5 mm under the board (room for the stick-on rubber feet), 12 mm above the PCB.
Files & notes
STL and 3MF for printing, STEP for remixing. Designed in Autodesk Fusion around the official reference model "Synaptics Coralboard SL" by Coral (Apache 2.0).
Honest note: this model was designed with AI assistance. It was built and checked digitally against the official reference CAD (no collisions with the board), but it has not yet been test-fitted on a physical Coralboard. If a port or tolerance needs a tweak, please post a Make or a comment and the files will be updated.
Images: the first four pictures are AI-generated photorealistic visualizations made from the CAD model, not photos of a real print. The other images are direct CAD renders. Real print photos will be added later.