Pimax Dream Air and Dream Air SE interface for Studioform v2 Pads
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Dream Air facial interface for the v2 studioform cushions
- Ocena
- 5 / 5
- Polubienia
- 12
- Pobrania
- 182
- Wydruki
- 1
- Wyświetlenia
- 644
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Virtual Reality
- Licencja
- Creative Commons — Attribution — Noncommercial
A remix of the original interface to suit the larger v2 pads. If you prefer the smaller one then see the original model and for now you would need to order the BSB pads from studioform… but I believe they intend to re-offer the v1 pads at some point.
At this point in time I've only done the “Max” version but intend to add a nominal (+3mm) and Long (+6mm) version when I have time and after some feedback. This Max version works great for me with the 12mm but may put some people too close - please note that sometimes being too close may cause issues with the eye tracking reliability so if you find issues with that try a spacer or one of the further offset versions when available.
If this design works well for you, and only if you feel like it and want to support ZeeFilamentFund, you can send me a small donation, totally optional and not in anyway required! https://ko-fi.com/zeeflyboy Many thanks to those of you who have kindly donated - it is much appreciated.
This interface reuses the default Pimax metal bracket which is easily removed using a jewellers screwdriver (appears to be PH00 head) and is fully reversible with no damage as long as you are careful not to strip the screws.
Carefully remove the metal bracket from the stock interface (highly recommend a magnetised screw driver or at least sticking a neodymium magnet to you standard driver. Fit the bracket to the printed interface seating the top first... not all screws are required if you can't be bothered, at least fit the inner 4 screws.... outer 4 screws are optional. If screws are difficult to drive in it may be due to print tolerances... you can open them up again with a 1mm drill bit (they are scaled at 1.2mm in the print file to try and make it easier) DO NOT FORCE THEM AS THEY WILL STRIP.
When mounting the new interface, fit bottom side first and then rotate the top into place, ensuring the alignment pin on the bracket seats fully, depending on print tolerances you may need to press behind the alignment pin on the bracket firmly with your thumb to pop it into place the first time.
I have initially just released my personal favourite which is the closest version (Max), intended to be used with the thicker cushion from studioform (12mm in my case). Spacers and different cushion thicknesses can be used to adjust the fit.
The foams intended to be used are by studioform, personally I find the fabric ones most comfortable - just change them occasionally and treat them as ultimately disposable!
If you are going to purchase these and wanted an alternative way to help ZeeFilamentFund you can use these referral links, no cost to yourself and I get a few pennies in the jar.
Full kit: Pimax Dream Air DIY Face Pad Modders Kit | Studioform Creative
12mm foam Thick Replacement Face Pads For Pimax Dream Air X1-P Interface 12mm (2 Pack) | Studioform Creative
8mm foam Replacement Face Pads For Pimax Dream Air X1-P Interface Standard 8mm (2 Pack) | Studioform Creative
3mm (why!?) foam Ultra Thin Replacement Face Pads For Pimax Dream Air X1-P Interface 3mm | Studioform Creative
If DIY ain't for you - Full Studioform interface Pimax Dream Air Interface X1-P Kit | Studioform Creative
I recommend the thin style hook tape Studioform uses (ultra low profile Velcro), if you have their full kit then you can trim the stock velcro slightly and get a good enough fit with a few minutes and some scissor work. Easier no-skill option is just to cut multiple tabs and that works fine too (see photos). Any hook side adhesive tape should work though the ultra low profile is best.
Printing advice - you do you. However I recommend a fairly low layer height (eg 0.16) to improve overhang performance, and I tilt back 125 degrees from the STL/3MF and change support threshold to 40 degrees to ensure really solid supports that won't allow any shifting.
Opional Post Processing - carefully remove support material and I would recommend a quick sand of the sharper edges. If you want to finish them like in the above photos give them a first wet sand with 240 grit, allow to dry thoroughly. Do several coats of filler primer and allow to cure properly... wet sand over again with 240 or 400 grit and then one final very light coat of primer. Finish in the paint of your choice, just choose something fairly tough... I used generic black car bumper paint.