1 / 56

R3D Flsun I3 Mod Kit Part 3

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

JamesK1

@JamesK1_26547

R3D Flsun I3 Mod Kit This is part 3 of 3 of my collection of mods for the Flsun I3 printer. These are mainly cosmetic…

Ocena: 0 / 5
Polubienia: 1
Pobrania: 15
Wydruki: 0
Wyświetlenia: 208
Oceny: 0

Aktualizacja u źródła: 2 maj 2022

Informacje o modelu

Źródło: Printables
Kategoria: Other Ideas
Licencja: Creative Commons — Attribution

Szczegóły Pliki (35)Wydruki i komentarze (Wydruki: 0) (Komentarze: 0)Remiksy (0)Kolekcje (2)

R3D Flsun I3 Mod Kit

This is part 3 of 3 of my collection of mods for the Flsun I3 printer.

These are mainly cosmetic and some safety improvements but not critical. Also your setup may not warrant these.

There's a lot in here but I had more than enough spare screws and nuts from the printer build for them. Well, except for the countersink M3 screws I used for the heatbed leveling mounts.

Note that some of these are dependent on specific hardware so please be certain it will fit your needs.

Update 05/22/2017 - Added a new spool holder - 2020 Mounted Spool Roller Update 07/23/2017 - Added a 40mm fan shroud + Fang combo for the E3D v6 clone hotend

List of Printed Parts:

PSU Case -- specifically designed around the TriGorilla Mosfet. MKS Controlboard Case -- I designed it around mine which is the MKS Gen_L V1.0. It may fit other MKS boards but I'm not sure. Also there's a couple versions depending on what you may want as far as wiring options. Spool Holder 2020 Mounted Spool Roller Stubby Parts Cooler -- While I think the fang cooler is a better choice, if you don't have a working parts cooler now, you may want to print the stubby to help print the fang as it can be difficult without a cooler. Or, print very slow with an external fan pointed at your bed. Induction Sensor Mount Y Bearings Holder for Igus Bearings M3 Double Nut Bed Adjustment Knob E3D v6 Heatsink Fan Shroud (40mm) & 5015_40 Fang Combo -- You may need to use the Stubby cooler to get the fang printed properly. This combo also requires a 40mm fan for the heatsink and 4 x M3x16mm hex screws.

Recommended Hardware

Titan Extruder w/ Bowden adapter
TriGorilla Mosfet
V6 Hotend
E3D V6 Silicon Sock for the heater block - prevents filament from getting stuck on the heater block and burning.
Igus Delrin Linear Bearings
M3 x 35mm Countersunk flat head hex screws - will require a drill to countersink the mounting holes on the aluminum heatbed.
PEI sheet 220mm x 220mm (or 10in x 10in) - I absolutely love this stuff! You may need to cut it to fit.
Aluminum Bed Carriage Plate (RepRap or Winhao Duplicator version).
MKS LV8729 stepper motor driver - Set it to 1/64th per step and the motors are quiet! Well.. much quieter than they used to be. :) Do a lot of research before using these. If you screw something up, I'm not responsible.
608ZZ Skateboard Bearings

=====================================================