1 / 4
SmoothRoll - Bearing Sleeve for Prusa injection moulded spool holder — zdjęcie 1
1 / 4

SmoothRoll - Bearing Sleeve for Prusa injection moulded spool holder

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Bearing sleeve for smoother spool rotation on the Prusa MK4 spool holder. Includes a slim installation key.

Ocena
0 / 5
Polubienia
0
Pobrania
2
Wydruki
0
Wyświetlenia
11
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

SmoothRoll adds a bearing-supported sleeve to the Prusa injection-moulded spool holder arm, helping filament spools rotate smoothly instead of sliding directly against the fixed arm.

The sleeve runs on two bearings and has low, rounded end lips, allowing spool changes without removing the arm. A slim installation key is included to help turn the original arm into its locked position.

COMPATIBILITY

Designed for the Prusa injection-moulded spool holder arm shown in the photos.
Prusa lists its injection-moulded spool holder as compatible with:

  • MK2, MK2S, MK2.5 and MK2.5S

  • MK3, MK3S and MK3S+

  • MK3.5 and MK3.5S

  • MK3.9 and MK3.9S

  • MK4 and MK4S

This is Prusa's compatibility list for the original holder, not a claim that SmoothRoll has been tested on every printer listed. Holder versions may vary, so compare your arm with the photos and dimensions before printing.

Prusa's spool-holder product page: https://www.prusa3d.com/product/spool-holder/

SmoothRoll dimensions:

  • Minimum spool centre-hole diameter: 50 mm

  • Maximum spool width: 80 mm

  • Sleeve diameter: 42 mm

  • Rounded end lips: 46 mm

  • Bearing adapter bore: 24.05 mm

This design is intended for the arm shown in the photos, not other spool-holder designs used on MINI, XL, CORE One or MMU setups.

PARTS REQUIRED - Print one of each included STL:

  • 01_Bearing_Sleeve.stl

  • 02_Front_Bearing_Adapter.stl

  • 03_Rear_Bearing_Adapter.stl

  • 04_Stop_Collar.stl

  • 05_Installation_Key.stl

Additional hardware:

  • 2 × 6805 / 61805 bearings, 25 × 37 × 7 mm

  • 1 × M3 flat-point grub screw for the stop collar; approximately 5 mm long, check engagement

  • Your existing Prusa injection-moulded spool holder arm

An M3 tap is recommended for preparing the stop collar's pilot hole, but is optional. An M3 screw can usually be threaded directly into the printed hole. Start it straight and tighten gently to avoid splitting the collar or stripping the plastic.

The installation key itself needs no additional hardware.

PRINT SETTINGS

The parts were developed using PLA and a 0.4 mm nozzle.
Default settings in the supplied 3MF projects:

  • 0.20 mm layer height

  • 3 perimeters

  • 15% infill

Sleeve and adapters:

  • Use the supplied orientation and support settings

  • Remove supports carefully from the internal bearing shoulders

  • Clear all support material from the bearing seats before assembly

Installation key:

  • Print flat in the supplied orientation

  • No supports required

Thin sections may print solid because the perimeters and top/bottom layers fill the available space, even with 15% infill selected.

The supplied 3MF projects contain separate setups for the sleeve assembly and installation key. They are configured for a Prusa MK4 with a 0.4 mm nozzle. Select your own printer and filament profiles before slicing if your setup differs.

Bearing fits depend on printer calibration, material and slicing settings. Remove small burrs or strings before assembly and do not force parts that are excessively tight.

ASSEMBLY

  1. Remove the original arm from its mounting bracket.

  2. Slide the front bearing adapter onto the arm from the mounting end, with its flange facing the arm's free end disk.

  3. Insert the front bearing into the sleeve, then slide the sleeve and bearing onto the arm and front adapter.

  4. Fit the rear bearing and rear adapter from the mounting end. The rear adapter's flange faces the mounting bracket.

  5. Prepare the stop collar's pilot hole. Tapping it M3 is recommended, but the M3 grub screw can usually be screwed directly into the printed hole. Start the screw straight and advance it gently. If resistance is excessive, back it out and use a tap instead of forcing it.

  6. Install the stop collar and gently tighten the grub screw. Leave a little axial clearance so the sleeve rotates freely without rubbing against the original end disk or squeezing the bearings.

  7. Reinstall the arm and check that it locks securely. Confirm that the sleeve rotates freely before loading a spool.

When pressing a bearing into the sleeve, press on its outer ring. Support the inner ring when fitting it onto an adapter. Avoid transferring assembly force through the bearing balls.

USING THE INSTALLATION KEY

The key engages the slot between the sleeve and the original arm's end disk.

Slide the thin head into the gap and engage the central tab with the slot. The tab's narrower side should face the sleeve. Turn in the plane of the tool to lock or unlock the arm.

The key has a 1.2 mm thick head and a 2.9 mm thick handle. Its tapered tab was designed around a slot approximately 1.6 mm high and 9.9 mm wide.

The key design has been printed and successfully tested on my holder. The supplied 15% infill / 3-perimeter profiles have been checked in the slicer; these revised settings have not yet been physically retested.

Check engagement before applying force. The key is a turning tool, not a pry bar.

FILES

The download includes:

  • Five individual STL files with English filenames

  • SmoothRoll_Sleeve_MK4_PLA_04.3mf — sleeve assembly

  • SmoothRoll_Key_MK4_PLA_04.3mf — installation key

The original Prusa arm and the other mounting parts visible in the photos are not included.

This is an independent accessory project, not an official Prusa product.

Tagi