1 / 18
Elektronisches Handrad CNC — zdjęcie 1
1 / 18

Elektronisches Handrad CNC

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

DIY E-Handrad bis 4 Achsen / E-Handwheel 4 axis

Ocena
0 / 5
Polubienia
2
Pobrania
5
Wydruki
0
Wyświetlenia
37
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Hier findet Ihr Modelle für ein elektronisches Handrad was ich mir gebaut habe um es an meiner CNC Fräse mit Linux CNC zu verwenden.

Die Bauteile die benötigt werden findet Ihr unten am Ende der Beschreibung aufgelistet.

Das Handrad funktioniert mit einem Raspberry Pi Pico und wird via USB angeschlossen. Auf dem Pi läuft ein kleines Python Skript, für Linux CNC wir das gegen Skript in den LinuxCNC-Konfig-Ordner gelegt und in der custom.hal müssen die neuen Pins konfiguriert werden. Die Skripte sowie das PinOut des Handrades findet Ihr ebenfalls im Download Bereich.

Thonny, das Programm zum Pi Pico Beschreiben sowie die Firmware RPI_PICO-20260824-v1.29.0.uf2 müsst Ihr von den entsprechenden Seiten im Netzt ziehen, diese dürfen hier nicht hochgeladen werden.

Handrad Funktionen:
  1. Achsauswahl (X, Y, Z, A , Aus(könnte auch als 5. Achse definiert werden)

  2. Schrittwahl (Kontinuierlich, 1,0mm, 0,1mm, 0,01mm und 0,005mm)

  3. Vorschub Poti (0% - 120%)

  4. An/Aus Schalter mit Beleuchtung (Ausgeschaltet reagiert das Handrad auf keine Eingabe)

  5. Null-Taster, Setzt die aktuell ausgewählte Achse auf Null im G54 Koordinatensystem

Vorgehen:
  1. RP-Pico flashen (Pico im Bootsel modus starten und die Datei "RPI_PICO-20260824-v1.29.0.uf2" per Drag and Drop auf den Pico ziehen, der Pico startet nun neu

  2. Mit dem Programm "Thonny" kann nun der Pi-Pico-Py-Skript auf den Pi kopiert werden und als "main.py" abgesspeichert werden

  3. Am LinuxCNC Rechner erstellt Ihr nun die Datei "pico_handwheel.py" und fügt den LinuxCNC-Py-Skript in die Datei ein.

  4. Die LinuxCNC custom.hal muss dann noch mit den Elementen aus "LinuxCNC-Custom-Hal-Ergänzen" ergänzt werden

  5. Fräsen und Spaß haben

Bitte seht davon ab mich nach irgendwelchen Änderungen an den Skripten zu machen, das ist die Konfig die bei mir funktioniert und diese Skripte wurden mithilfe von KI-erstellt. Ich selbst bin darin nicht sehr firm. 

Gedruckt habe ich alle Teile ohne Stützmaterial und in PETG CF was sehr gut funktioniert hat.

Viel Spaß beim bauen, Wenn Euch das Modell gefällt würde ich mich über ein like freuen.

Here you'll find models for an electronic handwheel that I built to use with my CNC milling machine running Linux CNC.

The required components are listed at the end of the description below.

The handwheel works with a Raspberry Pi Pico and connects via USB. A small Python script runs on the Pi; for Linux CNC, this script is placed in the LinuxCNC configuration folder, and the new pins must be configured in the custom.hal file. The scripts and the handwheel pinout can also be found in the download section.

Thonny, the program for programming the Pi Pico and the firmware RPI_PICO-20260824-v1.29.0.uf2 must be downloaded from the respective websites; these cannot be uploaded here.

Handwheel Functions:
  1. Axis Selection (X, Y, Z, A, Off (could also be defined as a 5th axis))1

  2. Step Selection (Continuous, 1.0 mm, 0.1 mm, 0.01 mm, and 0.005 mm)

  3. Feed Rate Potentiometer (0% - 120%)

  4. On/Off Switch with Illumination (When switched off, the handwheel does not respond to input)

  5. Zero Button: Sets the currently selected axis to zero in the G54 coordinate system

Procedure:
  1. Flash the RP-Pico (start the Pico in boot mode and drag and drop the file "RPI_PICO-20260824-v1.29.0.uf2" onto the Pico; the Pico will now restart).

  2. Using the program "Thonny," the Pi-Pico-Py script can now be copied to the Pi and saved as "main.py."

  3. On the LinuxCNC computer, create the file "pico_handwheel.py" and insert the LinuxCNC-Py script into it.

  4. The LinuxCNC custom.hal file then needs to be supplemented with the elements from "LinuxCNC-Custom-Hal-Add".

  5. Mill and have fun!

Please refrain from asking me to make any changes to the scripts; this is the configuration that works for me, and these scripts were created using AI. I am not very experienced with it myself.

I printed all parts without support material. and in PETG CF, which worked very well.

If you like the model, I would be happy if you leave me a like

BOM:

1x Null-Taster / Zero-Switch:

https://amzn.eu/d/0iu4MLlq

1x An-Schalter / on-Switch:

https://amzn.eu/d/0i2Qqglo

2x Position Schalter / Position Switches: 

https://amzn.eu/d/07PCG9yC

1x 100ppr Encoder:

https://amzn.eu/d/0crat8TT

1x Poti 10K:

https://amzn.eu/d/0iptkwA5

1xRaspberry Pi Pico:

https://amzn.eu/d/08kX5TQG

1x Micro USB Kabel / cable

1x PG11 Kabelverschraubung / Kableconnector

5x M4 Gewindeeinschmelzhülsen / Threded Heat Inserts

5x S4 Schrauben / Screws (Gehäuse / Housing) 

4x M2 Schrauben / Screws (Pi Pico) 

Tagi