W1SFR Blackstone Paddle Carry Case with Magnetic Lid and Cable Bay
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Two-piece carry case for the W1SFR Blackstone paddle: magnetic lid, cable bay, and the paddle works in the base.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 9
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Overview
A two-piece protective carry case for the W1SFR "Blackstone" soapstone Cootie/Paddle. The paddle sits in a fitted pocket in the base with its feet in sockets, and a separate lid drops on and is held by four pairs of 8 x 2 mm magnets. A cable bay behind the paddle holds the coiled cord, so the whole setup comes out of a bag and goes on the table in one piece. The split line is stepped low at the front, so you can operate the paddle in the base with the lid off.
On the Air
The Blackstone is a heavy, hand-waxed soapstone base with a torsion bar mechanism. That is great on the desk and less great rattling around in a go-bag next to a battery and a coax roll. This case is for POTA, SOTA, field day and travel: the stone, the levers and the tower are all fully enclosed, and nothing touches the fingerpieces or the tower except the cradles that hold them in place.
At an activation, lift the lid and the paddle is ready to send right in the base. The cord stays plugged in and lives in the cable bay. When you are done, coil the cord into the bay, drop the lid on, and go.
The stone weighs about 500 g, so carry the case base-down. The magnets hold the lid on, not the full weight of the paddle hanging from it.
Print Settings
- Printer: Bambu Lab X1C/X2D, 0.4 mm nozzle
- Material: plain PETG for both parts. Do not use carbon-fiber filled filament for this case: CF can mark the waxed soapstone, and the lid cradles load across layer lines, where plain PETG holds up better.
- Layer height: 0.20 mm
- Wall loops: 5
- Infill: slicer default for the body, with a 100% infill modifier on the lid cradles (the walls around the fingerpiece and the torsion tower)
- Supports: none. Every overhang is 45 degrees or steeper in print orientation.
- Orientation: base floor-down, lid upside down (roof on the bed). The 3MF is already laid out this way, with base and lid as separate objects. Printing the lid upside down puts the cradle roots on the bed so the fillets flare outward and print clean.
Hardware and Assembly
- 8x 8 x 2 mm neodymium disc magnets (4 in the base, 4 in the lid)
1. Measure your magnets before you start. Some "8 x 2" magnets are actually 1/16 in (about 1.6 mm) thick, which will sit recessed and hold weakly.
2. Stack all eight magnets, then mark the top face of the stack. This keeps the polarity consistent.
3. Press four magnets into the base pockets, marked face up. The pockets have crush ribs, so press firmly with a flat tool. In some cases a bit of CA glue may be needed.
4. Set the lid on the base with no magnets in it yet. Drop each remaining magnet onto its base magnet so it attracts, then lift it off and press it into the matching lid pocket with the face that was touching still facing down.
5. Check the closure. Set the paddle in the base with its feet in the sockets, route the cord through the floor channel and the divider notch into the bay, and close the lid.
Design Notes
- Pocket: sized to the W1SFR nominal 3 x 5 in base plus 1 mm per side (78.2 x 129 mm). My stone measured 73.5 x 125.9 mm and floats a little in that, which is fine for a protective case. The feet sockets (16 mm dia, 1.5 mm deep) are placed between the measured and nominal foot positions, so stones that vary a mm or two still drop in.
- Split line: a three-level stepped split. It is low at the fingerpiece (z 10) so you can reach the levers, at the stone top through the middle, and high at the rear (z 50) so the cable bay is deep. The steps and a 1.5 x 4 mm tongue along the side walls key the lid so it only goes on one way.
- Cord path: the Blackstone's cord exits under the stone rather than out the back. The case runs it in the gap under the stone plus a 7 x 1.5 mm floor channel. That gives about 6.5 mm of headroom for a 3.5 mm cord, through a notch in the divider and up a ramp into the bay.
- Lid cradles: U-channels close around the fingerpiece (18 mm gap) and the torsion tower (9.5 mm gap). The walls taper from 3.2 mm at the tip to 5.2 mm at the root, with fillets and gussets, because these walls are loaded across layer lines. The tower cradle is open at the front because the tower sits 12 mm in from the rear of the stone.
- Side rims: rims on the lid ride 0.5 mm above the stone top so it cannot lift in transit. They start behind the side adjustment knobs to stay clear of them.
- Magnet pockets: each 8.4 mm pocket has three crush ribs with a 7.9 mm inscribed diameter, so magnets press in and stay put without glue. The ribs have a lead-in at the mouth.
- Edges: every edge is chamfered or filleted for its print orientation.
- Development: this is a sibling of my W1SFR Fat Boy carry case and uses the same construction, adapted for the Blackstone's longer stone, set-in tower, under-stone cord exit and side knobs. The design was drawn and checked before modeling: no interference with the paddle at measured and nominal size, and no overhangs needing support.
If you print one, I'd like to see a make, and fit reports from other Blackstone owners are welcome.