Clearance and vehicle check gauge – free, for Z, N, TT and H0
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Free check gauge per scale: clearance for platforms, portals, signals plus a vehicle envelope window (NEM).
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 4
- Wydruki
- 0
- Wyświetlenia
- 9
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Test Models
- Licencja
- Creative Commons — Attribution
Free check gauge for each scale: clearance for platforms, portals and signals, plus a window with the vehicle envelope. Dimensions from the current NEM editions.
Before you print a portal, a platform or a load, this gauge shows how much room vehicles need. There are two parts per scale: a clearance gauge that you push along the track and a vehicle gauge that you push a vehicle through.
Clearance gauge: its outer contour is the clearance without overhead line. It rests on the rail heads, and a tongue between the rails keeps it centred. Whatever it touches as you push it along reaches into the clearance.
Measuring nose for platform and ramp: the step at the bottom shows how close and how high an edge may be (H0: 21 mm from the track axis, 11 mm high).
Vehicle gauge: a window with the vehicle envelope, open at the bottom for wheels and rails. If a vehicle or its load touches it, it is wider or taller than the envelope.
Current editions: clearance to the 2019 edition (57 mm high in H0, an older edition gave 59 mm), vehicle envelope to the 2024 edition.
In the set per scale:
Z: clearance 20 × 23 mm, edges up to 9 mm from the track axis and 4.5 mm high; vehicle envelope 17 × 22 mm
N: clearance 27 × 31 mm, edges up to 12.5 mm from the track axis and 6 mm high; vehicle envelope 23 × 30 mm
TT: clearance 36 × 41 mm, edges up to 16 mm from the track axis and 8 mm high; vehicle envelope 30 × 40 mm
H0: clearance 48 × 57 mm, edges up to 21 mm from the track axis and 11 mm high; vehicle envelope 40 × 55 mm
Scales: One variant per scale: Z (1:220), N (1:160), TT (1:120) and H0 (1:87). Each variant contains the single parts and a collection plate with all parts of the scale (3 mm apart).
Dimensions: Dimensions taken from NEM 102 (2019 edition) and NEM 301 (2024 edition). The clearance gauge rests on the rail heads and needs no height adjustment. The feet of the vehicle gauge sit at rail-top level (height offset 0); if your track sits higher than the baseboard, shim both feet by that height. The space for an overhead line is not included, because the standard only allows it to be derived from the drawing. The gauge itself has not been tested on a layout yet; how accurate it turns out depends on your printer.
Material: PLA is enough because the layout stays indoors; PETG works too. 0.4 mm nozzle, ideally 0.12 mm layers, no supports.
Not a toy. Model-making accessory for model railway hobbyists aged 14 and up; contains small parts that can be swallowed, keep out of reach of small children.
Variants (all included)
Z (1:220)
N (1:160)
TT (1:120)
H0 (1:87)
Print settings
Material: PLA (or PETG). PLA is enough because the layout stays indoors; PETG works too.
Layer height 0.12 mm, 2 walls, 15 % infill, no supports.
Orientation: Lying flat, no supports.
Both gauges lying flat, as the files are laid out.
Print time approx. 41 min and about 8 g (default variant H0: collection plate with all parts; other variants differ).
Safety
Not a toy. Model-making accessory for model railway hobbyists aged 14 and up; contains small parts that can be swallowed, keep out of reach of small children.
FAQ
How do I use the two gauges? Clearance gauge: stand it across the track with the tongue between the rails, then push it slowly past the platform, portal or signal. Vehicle gauge: stand it across the track (feet beside the track, shimmed if needed) and push the vehicle through by hand.
Does the gauge apply in curves too? No, it shows the clearance on straight track. In curves it gets wider depending on the radius; the curve clearance gauge covers that.
Does the part carry current or work? No. Nothing in this range carries current; detail parts are dummies.
How it's made
Parametric CAD (build123d, Python), exact solids. The CAD code was written with an AI assistant and checked by us; no AI-generated meshes or images. Renders are made from the CAD in Blender and show the part in simple staged scenes (placeholder track without brand, cutting mat); they are not photos.
License
CC BY 4.0: you may share and adapt it, also commercially, as long as you credit Magmacode and link the license (https://creativecommons.org/licenses/by/4.0/).
Matching gauges, loads, tunnel portals and scenery parts for model railways are in the Magmacode profile.
