Eurorack fit gauge 3U and 1U – free, with hole pattern, 1U tiles and tolerance comb
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Free Eurorack test part: 3U piece with 8 HP and hole pattern, 1U tiles (Intellijel, Pulp Logic), tolerance comb.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 4
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Test Models
- Licencja
- Creative Commons — Attribution
Free test part for all Eurorack parts: 3U piece with 8 HP and hole pattern, 1U tiles in Intellijel and Pulp Logic format, tolerance comb.
Fits: Eurorack 3U (8 HP piece with the Doepfer A-100 hole pattern) and the two common 1U tile formats, Intellijel and Pulp Logic. Not affiliated with Doepfer, Intellijel or Pulp Logic; the names only identify the sources of the dimensions and the 1U formats, and the part is not an accessory by any manufacturer. No logos and no lettering on the parts.
Before you print a panel or a stand, this gauge shows in a few minutes whether the dimensions suit your case and your printer. All four parts sit on one print plate.
3U piece, 8 HP: 40.3 × 128.5 mm (Doepfer actual width), four slots Ø 3.2 × 4.6 mm at 7.5 and 32.9 mm from the left, 3 mm from the top and bottom edge. You screw it in like a module and see whether hole pattern, screws and neighbour panels fit.
1U in Intellijel format: 40.3 × 39.65 mm, slots 3 mm from the edge (hole spacing 33.65 mm).
1U tile in Pulp Logic format, 6 HP: 30.23 × 43.18 mm, four holes Ø 3.2 mm for M2.5. The two 1U formats differ in height and are not interchangeable.
Tolerance comb: three slots for a 2 mm panel with +0.2, +0.4 and +0.6 mm (one, two, three dots). Push the edge of a real module panel in: the narrowest slot it enters without force shows how much your printer closes up inner dimensions.
Dimensions: Dimensions taken from Doepfer A-100, Construction Details, Doepfer hole drawing, Intellijel 1U Technical Specifications and Pulp Logic, About 1U Tiles; our part has not been tested on a case yet. The Pulp Logic tile is 30.23 mm wide, the middle of the maker's tolerance (30.48 mm, +0/−0.51). Estimated are the slot length (our own rule; it covers the hole offsets 7.45, 7.5 and 7.62 mm that are in use) and the horizontal spacing of the Intellijel tile (not dimensioned there, assumed as for 3U). How accurate the gauge turns out depends on your printer; that is what the comb is for.
Material: PLA is enough, PETG works too: the parts carry hardly any load and do not get hot in the case. Do not leave them in the sun or a hot car, PLA softens from about 55 °C.
Print settings
Material: PLA (or PETG). Do not leave it in the sun or a hot car: PLA softens from about 55 °C.
Layer height 0.2 mm, 2 walls, 15 % infill, no supports.
Orientation: Flat, front face down, as the plate is laid out.
All parts lie flat, front face down; the bottom edges have a 0.4 mm chamfer against elephant's foot.
Print time approx. 56 min and about 19 g (collection plate with all parts).
Hardware (not included)
4 × M3 screw from your case (usually M3×6, pan head), for 3U and Intellijel 1U
4 × M2.5 screw, only for the Pulp Logic tile
Assembly
Switch the case off. Screw the 3U piece to a free spot on the rails with M3 screws, ideally right next to a module.
Check: does it sit between the neighbours without jamming, do the slots meet the threads, does it lie flat? With a 1U row, check the matching tile the same way.
Tolerance comb: push the edge of a module panel into the slots and note which one fits.
Safety
The part has no electronics and carries no current. Switch the case off before fitting or removing panels.
Fit
Slots ± 0.7 mm horizontally; Pulp Logic tile in the middle of the tolerance.
FAQ
The 3U piece jams between my modules. What now? Like Doepfer's, our panels are about 0.3 mm narrower than the grid. If it still jams, your printer prints outer dimensions too large (over-extrusion or elephant's foot). Calibrate the flow or scale the panels to 99.5 % in width.
Which 1U format does my case use? Intellijel 1U panels are 39.65 mm tall, Pulp Logic tiles 43.18 mm. If your case manual does not say, hold both tiles against the 1U row: only one fits.
Have you printed the part and tested it on a case? Not yet. The dimensions come from the sources named; the gauge has not been printed or tested on a case yet. That is exactly what it is for: it is the first part you print, and it shows whether your case and printer suit our dimensions.
Which material? PLA is enough, PETG works too: the parts carry hardly any load and do not get hot in the case. Do not leave them in the sun or a hot car, PLA softens from about 55 °C.
Does the part carry current? The part has no electronics and carries no current. We deliberately do not offer bus boards, power supplies or device adapters with electronics.
How it's made
Parametric CAD (build123d, Python), exact solids. The CAD code was written with an AI assistant and checked by us; no AI-generated meshes or images. Renders are made from the CAD in Blender and show the part in simple staged scenes (placeholder case without brand, wooden table); they are not photos.
License
CC BY 4.0: you may share and adapt it, also commercially, as long as you credit Magmacode and link the license (https://creativecommons.org/licenses/by/4.0/).
Matching Eurorack panels and tilt stands for synth cases are in the Magmacode profile.
