1 / 4
Koi Stack – Balance Game — zdjęcie 1
1 / 4

Koi Stack – Balance Game

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Stacking balance game with 12 chunky koi fish and a color die that picks which one goes on the tower next.

Ocena
0 / 5
Polubienia
61
Pobrania
71
Wydruki
0
Wyświetlenia
375
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Board Games
Licencja
Creative Commons — Attribution — Noncommercial

Want to sell prints of this model? A commercial license is available on my Patreon:
https://www.patreon.com/Elizabeth3D

Like my free models? Support me on Ko-fi:
https://ko-fi.com/elizabeth3d

Koi Stack is a stacking balance game with a color die: twelve chunky koi fish in twelve swimming poses, and the die tells you which one goes on the tower next.

Design Concept

Four real single-color koi varieties, three fish of each: red Benigoi, gold Ogon, black Karasu and white Platinum. The koi hook and lean on each other as the tower grows, until it wobbles and comes crashing down.

Purpose

A family game for 2 to 4 players. Kids can play it without the die.

How to Play

  • Setup: roll the die and lay one koi of that color flat on the table: that's the base of the tower.

  • Take turns: roll the die and stack one koi of that color anywhere on the tower: flat, on its edge or hooked on another fish.

  • Pink face: free choice, stack any koi you like.

  • No koi of that color left? Roll again.

  • If any koi falls off on your turn, you lose. All twelve koi on the tower? Everybody wins: mix them up and play again.

  • Kids variant: leave the die out and stack any koi you like.

What's in the Box

  • 12 koi, all exactly 20 mm thick and about 70 mm long, with scales, gill and eye engraved on both faces.

  • 1 color die (25 mm): a grey body with six press-fit discs, four colors on the sides and two pink free-choice faces on top and bottom.

Print Settings

  • Printer: printed on a Creality SPARKX i7, 0.4 mm nozzle. Material: PLA. Layer height: 0.20 mm. All inside the 3MF, set with the Creality SPARKX i8 0.4 nozzle system profiles: just open it as a project

  • One color per plate: no filament changes and zero purge waste, so you don't need a multicolor system to print it in full color

  • Plates 1 to 4: three koi and the die disc of their color, in red, gold, black and white. The koi print flat on one face, with no supports.

  • Plate 5: the grey die body, with one of its free-choice sockets down; supports only inside the bottom socket (pull them out with tweezers).

  • Plate 6: the two pink free-choice discs.

  • Keep the walls and infill set in the 3MF: they change how much each koi weighs, and so how the tower balances

  • Do not scale the die: the discs have 0.15 mm of clearance at 100%

Assembly

  1. Remove the support from inside the bottom socket of the die.

  2. Press the four color discs into the four side sockets, and the two pink discs into the top and bottom sockets (opposite each other, so the die stays balanced).

  3. If a disc feels loose, add a tiny drop of glue. The koi need no assembly.

Tagi