1 / 2
Black Cat Kit Card – Slot-Together Halloween Cat — zdjęcie 1
1 / 2

Black Cat Kit Card – Slot-Together Halloween Cat

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A sitting black cat that slots together from one flat printed card. No glue or supports; just nippers or scissors.

Ocena
0 / 5
Polubienia
4
Pobrania
0
Wydruki
0
Wyświetlenia
13
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Standard Digital File License

A black cat that stands up from a flat card.

Snip 7 flat parts off the card, slide them together, and a sitting black cat appears. No glue needed; just nippers or scissors. No supports, 0.2 mm layers.

Assembled size: approx. 39 × 20 × 49 mm

Card: 117 × 78 mm (frame 2.4 mm thick, parts 1.8 mm thick). Fits the A1 mini (180 mm bed)

Filament approx. 11–12 g, print time approx. 33–35 min on the A1 and A1 mini, depending on infill (15–100 %)

Parts: body, 2 haunch plates, 2 paw plates, 2 foot fins = 7 pieces

Material: separate 3mf files for PLA and PETG. Same slot width; only the gates differ. The PETG version has thinner gates because PETG is harder to snap cleanly. The STL is the PLA version.

Print settings: layer height 0.2 mm (the parts are exactly 9 layers; other layer heights change the fit). Tested with the Bambu Studio standard settings (2 walls, 15 % infill). No supports, no brim.

Assembly

Step 1: Cut the gates on each part with flush cutters (nippers) or scissors. The gates are thin where they meet each part, so they break there.

Step 2: Stand the body plate up.

Step 3: Slide one foot fin up into the rear slot of the body. The two fins are the same shape.

Step 4: Slide the other foot fin up into the front slot of the body.

Step 5: On each side of the body, push a haunch plate (round plate with a foot) down onto the rear fin, so the slot in the plate goes over the fin. Left and right are the same shape.

Step 6: In the same way, push a paw plate (the smaller plate) down onto the front fin on each side.

Step 7: Press all bottoms flat against the table so the parts line up.

The slots are a light press fit.

Notes: contains small parts. Keep away from small children. Free for personal use. No guarantee of strength or dimensions.

How this was made: not an AI-generated mesh. I redesigned and test-printed this kit over and over by hand. An AI-generated image was used as a reference, and AI tools helped with the CAD scripts.

組み立てて立つ、黒猫のキットカード

平らな1枚のカードから7つの板を切り離し、溝に差し込むだけで座った黒猫が立ち上がります。接着剤は不要、道具はニッパーかハサミだけ。サポート無し、0.2 mm 積層。

完成サイズ:約 39 × 20 × 49 mm / カード:117 × 78 mm(枠の厚さ 2.4 mm、部品 1.8 mm)/ 重量:約 11〜12 g、印刷時間:約 33〜35 分(A1・A1 mini。充填 15〜100 % で変わります)

積層 0.2 mm。部品はちょうど9層です。他の積層でははめ合いが変わります。サポート無し、ブリム無し。

小さな部品があります。小さなお子様の手の届かない所で組み立ててください。個人利用向けの無料データです。強度・寸法の保証はありません。

Tagi