1 / 9
LOOKOUT – Coralboard SL edge-AI vision kit — zdjęcie 1
1 / 9

LOOKOUT – Coralboard SL edge-AI vision kit

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Tool-free magnetic case for the Synaptics Coralboard SL, fitted to the official CAD.

Ocena
0 / 5
Polubienia
1
Pobrania
0
Wydruki
0
Wyświetlenia
7
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Public Domain

The Coralboard SL exists to run AI on the device, and on-device AI almost always means a camera. So LOOKOUT is not just another box. It is a small system built around that job, and privacy is designed in:

  • Pod – a compact two-tone case with a tool-free magnetic lid and a coral-polyp vent bloom. It is fitted to the official Coralboard SL CAD.

  • Camera head – for the common 25 × 24 mm OV5647 / Pi-camera module, with a swivel privacy eyelid.

  • Bring your own action cam – a soft TPU privacy bezel with a tethered lens cap for the GoPro HERO13 (also HERO9–12), DJI Osmo Action 6 and Insta360 Ace Pro 2. These work as the Coralboard's USB camera.

  • One rail, many mounts – a magnetic dovetail rail under the pod takes GoPro, 1/4"-20 tripod and VESA 75 / wall adapters. A rail buckle adds a standard 3-finger GoPro mount to any of them.

  • Desk mast + GoPro link – a camera position for demos, doorbells, bird feeders and people counters.

Everything prints without supports on a standard 0.4 mm nozzle. Every load-bearing part is oriented so the load runs along the layers, not across them.

Bring your own action camera

A printed cage around an action camera needs tall, thin walls. On FDM those walls end up loaded across their layer lines and crack. So LOOKOUT follows what the community settled on:

  • Keep the camera in its own mount. The GoPro HERO has folding fingers. The DJI and Insta360 ship with a magnetic quick-release adapter that ends in standard 2 prongs. These plug straight into the LOOKOUT mast, the link, or the rail buckle on the VESA / wall plate.

  • TPU for everything that wraps the body. The privacy bezel is a soft front bumper. It grips the top and bottom edges and leaves the side faces free: doors, battery and USB-C stay usable. Its lens cap is tethered and carries a closed-eye icon. It is printed flat, in one piece, with no supports.

Camera

Body (W × H × D)

Connects to the Coralboard

Mounts with

GoPro HERO13 Black (HERO9–12 same body)

71.8 × 50.8 × 33.6

USB-C; webcam mode streams over USB networking (Linux tools exist)

its folding fingers

DJI Osmo Action 6

72.8 × 47.2 × 33.1

standard USB webcam (UVC)

DJI quick-release adapter (in the box)

Insta360 Ace Pro 2

71.9 × 52.2 × 38.0

USB webcam mode

Insta360 quick-release mount (in the box)

Power: the Coralboard's USB-A port supplies about 0.6 A, and action cameras charge while connected. Use a powered USB hub, or keep the camera battery in.

Print settings

PrusaSlicer, 0.4 mm nozzle, 0.2 mm layers, no supports. Every file is already oriented for printing.

Part

Orientation

Material

Notes

pod_base

bottom on bed

PLA / PETG

3 perimeters, 15 % gyroid. Rail ceiling is a 20 mm bridge.

pod_lid

top face on bed

PLA / translucent PETG

Translucent PETG lets the heartbeat LED glow through the pores.

cam_body / cam_back

flat face on bed

PLA / PETG

cam_eyelid

flat

PLA

Detent bump up.

adapter_gopro / adapter_tripod / rail_buckle

standing on end

PETG

4 perimeters, 40 % infill. Fingers run horizontally.

adapter_vesa_wall

flat

PETG

4 perimeters.

mast_foot

flat

PLA

mast_pole / gopro_link

lying on their flat side

PETG

4 perimeters, 40 % infill.

privacy_bezel_*

front face on bed

TPU 95A

2 perimeters, 20 % infill, 20–25 mm/s. Black or coral.

Hardware

Qty

Item

Where

4

M3 × 6 pan / button head, zinc-plated steel (magnetic, not stainless)

board → base standoffs (self-tapping, Ø2.6 pilot)

4

4 × 3 mm neodymium magnets

lid pillars (CA glue)

1 + 1 per adapter

6 × 2 mm neodymium magnets

rail ceilings + each tongue (check polarity)

8

Bumpon Ø7.9 mm (optional)

pod and mast feet

4 + 1

M2 × 12, M2 × 5 low head

camera head, eyelid pivot

2–3

M5 GoPro thumb screws + M5 nuts

mast ↔ link ↔ camera / buckle

1

M4 × 25

mast foot → pole

1

1/4"-20 hex nut

tripod adapter

1

22-pin → 15-pin camera ribbon (Pi 5 style), 200–300 mm

Coralboard CSI → camera head

Assembly

  1. Glue a 6 × 2 magnet into the rail ceiling of the pod and the rail buckle. Glue magnets into the adapter tongues with the opposite pole out.

  2. Screw the board onto the base standoffs with the four steel M3 screws.

  3. Glue the four 4 × 3 magnets into the lid pillars, flush. The lid then snaps onto the screw heads.

  4. Pi camera: screw the module to the bosses through the back cover (M2 × 12) and route the ribbon through the back slot. Fit the eyelid with its bump toward the camera, and tighten the pivot until it clicks open and closed.

  5. Mast: push the pole into the foot and fix it from below with the M4 screw.

  6. Action cam: stretch the TPU bezel over the front of the camera from the top. Push the cap onto the lens for privacy, and let it hang on its tether when recording.

  7. Slide any adapter into a rail from either end until the magnets click.

Notes

  • The privacy bezels are built from the manufacturers' published body sizes and the official manual diagrams. TPU absorbs a few tenths of a millimetre; if the bezel sits loose, print it at 98–99 % scale, if it is tight, at 101–102 %.

  • mikroBUS click boards stand taller than the lid; use them with the lid off.

Files

15 print-ready 3MF files, one part per file, already oriented: pod_base, pod_lid, cam_body, cam_back, cam_eyelid, adapter_gopro, adapter_tripod, adapter_vesa_wall, rail_buckle, mast_foot, mast_pole, gopro_link, privacy_bezel_gopro_hero13, privacy_bezel_dji_action6, privacy_bezel_insta360_acepro2.

License: CC BY 4.0

Tagi