Monitor Handles v2 for Ergotron HX – Dual Front Grips, VESA 100, MSI MPG 491CQP
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
v2: two angled grips just in front of the screen's bottom edge, on a frame hidden behind the monitor.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 10
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Version 2 of my handle for a big monitor on an Ergotron HX arm. It's a completely new design – frame, grips and hardware are all different from v1 ([link to v1]).
WHAT'S NEW IN V2
v1 worked, but in daily use two things bothered me:
- The bar was hidden behind and below the screen. To grab it, my hand had to reach deep under the screen and kept hitting its bottom edge.
- The C-clip held the cable bundle tight. When I pulled the monitor forward, the cables went taut and the plugs came out.
v2 fixes both:
- Two separate grips, 200 mm apart, right in front of the bottom edge of the screen. They lean 20° towards you and their bottoms splay out 15°, so your wrists stay in a natural position. You hold them like two short joysticks.
- The frame stays inside the outline of the monitor – from the front you only see the grips.
- No cable clip. The cables hang loose with some slack, so nothing pulls on them when the monitor moves.
- Stronger print orientation: the frame prints flat and the grips print on their side, so the layers run along the parts that take the load.
PARTS
- Frame (220 × 134 × 36 mm): the same VESA plate part as v1 (it bolts on under the two bottom VESA screws), two legs down the back of the monitor and a crossbar under the back cover, 94–112 mm below the bottom VESA screws.
- Right and left grip (mirror images): a 20 × 20 mm neck goes down behind the thick lower part of the screen, turns forward under its bottom edge and ends in a Ø31–33 mm grip, about 100 mm long, with a Ø38 mm flange at the bottom. Each grip bolts to the frame with 2× M4 screws into heat-set inserts.
WILL IT FIT YOUR SETUP?
Designed for and tested on an MSI MPG 491CQP (49", 1800R, 8.1 kg) on an Ergotron HX arm. The grips follow the shape of the bottom of this monitor closely, so on another monitor check all of these:
1. VESA plate: the plate part is the same as in v1 – it lies flat on the arm's VESA plate under the two bottom screws, with an 80 × 13 × 7.5 mm pocket for the pressed rib on the HX plate. If v1 fits your setup, this part fits too (the v1 fit test checks it).
2. Back of the monitor: the legs are 24 mm wide, centred 30 mm left and right of the middle, and run 18–36 mm out from the VESA plate surface. On the 491CQP the ribs on the back stick out 7–11 mm, which leaves 7–11 mm of clearance. Anything sticking out more than about 15 mm in those strips will hit the legs. The back cover must end no lower than about 64 mm below the bottom VESA screws (on the 491CQP: 63 mm) – the legs turn forward and the crossbar runs under it.
3. Lower part of the screen: below the back cover only the lower part of the screen continues down. On the 491CQP it's 29.5 mm thick (glass to back) and its bottom edge is 117 mm below the bottom VESA screws. The necks pass 5 mm behind it and 6.7 mm under its edge. If your monitor differs by more than about 3 mm in either number, the necks will hit the screen or the grips will sit too far from it – the files would need changes.
4. Buttons: on the 491CQP the joystick is in the middle of the bottom edge. The grips are 100 mm left and right of the middle and the frame stays 36 mm behind the screen, so the joystick is still easy to reach.
5. Room under the screen: the grips hang about 115 mm below the bottom edge of the screen. My screen edge is 192 mm above the desk, so the grips end about 77 mm above it. The lowest monitor position is about 16 mm higher than without the handles.
HARDWARE
- 2× M4×18 socket head cap screw + 2× M4 washer (DIN 125, 9 mm outer diameter) – they replace the two bottom VESA screws, same as v1. The top two VESA screws stay.
- 4× M4×18 socket head cap screw – grips to frame.
- 4× M4 heat-set insert, up to 10 mm long. The holes are Ø5.9 × 11 mm deep. This fit my inserts – a Ø6.2 hole was already too loose.
PRINTING
- PETG. My PLA prototypes (thin walls, printed standing) cracked, and PLA slowly gives way under constant screw pressure.
- Profile 0.20 mm STRUCTURAL (Prusa CORE One+, 0.4 nozzle). Saved in the 3MF files: 6 perimeters, 6 top / 5 bottom layers, 40% cubic infill, 100% infill around every screw and insert, 12% gyroid inside the grips, organic supports from the build plate only, support blockers in every hole.
- Frame: flat, VESA side down, no brim. Supports go under the legs and into the pocket – remove every bit from the pocket, there's only 1.5 mm of clearance above the rib on the plate. About 178 g, 8 h.
- Grips: on their side, inner side down. This way the layers run along the neck, which is the most loaded part – printed standing, the layers there get pulled apart (my standing PLA prototype started to crack). To make the grip lie flat, its inner side is cut flat at the very top, above where your hand goes (about 22 × 28 mm). Supports go under the grip and leave a rough strip on its inner side – sand it with 120, then 240 grit. About 80 g and 3 h 50 min each, 3 mm brim.
- Altogether about 340 g of PETG and 15.5 h. Print the parts one at a time and make sure the spool has enough filament.
- The STL files are already oriented for printing.
ASSEMBLY
1. Inserts: two into the block of each grip. The holes lie horizontal in the print, so hold the grip with the hole facing up and press each insert straight down with a soldering iron at about 240 °C.
2. Lower the monitor all the way and support it from below (a box or a few books).
3. Remove the two bottom VESA screws. For a moment the monitor hangs on the top two – that's fine. Put the frame on, insert the M4×18 screws with washers and tighten firmly.
4. Slide each grip up from below, between the frame and the screen, until its block sits flat against the frame. Bolt it from the back of the frame with 2× M4×18 (the heads sink 7 mm into the frame). "Right" and "left" are as seen from your chair.
5. Cables: on the 491CQP the ports are on the right (seen from the back). Run the cables over the frame's crossbar (there's about 30 mm between it and the back cover) to the arm and leave 10–15 cm of slack, so nothing pulls when you bring the monitor forward.
6. After a week of use, tighten all screws once more.
The grips are for moving and tilting the monitor on its arm – not for carrying it or hanging on it. Don't yank.
Fan-made accessory, not affiliated with or endorsed by MSI or Ergotron. The product names are used only to say what it fits.