1 / 5
Wall Mount - Leroy Merlin Inspire Riz Solar Meshtastic/Meshcore Node Bracket (European Edition) — zdjęcie 1
1 / 5

Wall Mount - Leroy Merlin Inspire Riz Solar Meshtastic/Meshcore Node Bracket (European Edition)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Wall mount bracket to convert a Leroy Merlin Inspire Riz solar light into a Meshtastic or Meshcore node.

Ocena
5 / 5
Polubienia
1
Pobrania
4
Wydruki
1
Wyświetlenia
47
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Gadgets
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

Compatible Solar Light (Leroy Merlin Poland / Europe):

Reflektor solarny wbijany Riz 25 / 70 lm czarny 39 cm LED Inspire

This custom mounting bracket is designed to convert the widely available Inspire Riz solar spotlight (sold across Europe at Leroy Merlin and similar home improvement retailers) into a weather-resistant Meshcore / Meshtastic node or repeater.

Adapted specifically for the housing geometry of the European Inspire Riz spotlight, this Wall Mount STL is provided completely free here on Printables to help support and grow the European mesh community.

The bracket features a dedicated mount for either a Type N or SMA antenna bulkhead connector (COMING SOON), routing your antenna wire directly into the housing through existing openings for a clean, weather-tight setup.

🛠 Included in this Download: Wall Mount Version

  • Flat Backing Design: Features pre-spaced screw holes for securing directly to exterior masonry, wood siding, fences, or flat fascia boards.

  • Installation Tip: Mount this as high up on the fascia board or gable as possible so your antenna completely clears the roofline for maximum line-of-sight coverage.

  • Integrated Bulkhead Collar: Holds your N-Type or SMA bulkhead firmly upright to eliminate physical strain on the internal pigtail cable and radio connector.

🧰 Hardware & Component Recommendations (EU)

As an AliExpress affiliate, I earn a small commission from qualifying purchases made through the component links below at no extra cost to you.

For solar-powered node builds, nRF52-based boards are strongly recommended over power-hungry architectures like ESP32 because their ultra-low power consumption allows the internal battery to sustain operation even during cloudy European winters.

Popular nRF52-Based Boards

Power Management & Solar Control

Antenna & RF Hardware

Mounting Fasteners

  • Exterior-rated wood or masonry screws suited to your mounting surface.

Requirements & Notes

  • Band Requirement: European Meshcore and Meshtastic operations operate on the EU868 band. Verify that your radio hardware and antenna match this regional specification.

  • Build Tutorials & Channel: Check out the step-by-step conversion videos, assembly guides, and off-grid radio testing on my YouTube channel: https://www.youtube.com/@HacnCrap

  • ⚠ Installation Caution: When mounting the bracket, hand-tighten all screws until snug. Do not overtighten or drive high-torque power tools into the mounting ears, as this can easily crack or stress-fracture printed plastic.

Print Settings & Suggestions

Because this bracket is designed for permanent outdoor deployment, standard PLA will warp in the sun and degrade quickly under UV exposure.

  • Material: ASA is highly recommended for long-term UV resistance, weathering, and heat tolerance (PETG is the minimum acceptable alternative).

  • Wall Count: 5 to 6 perimeters/walls to ensure rigid structural integrity around the antenna collar, mounting flange, and gear head joint.

  • Infill: 20%–25% (Gyroid recommended for isotropic mechanical strength).

  • Supports: Tree / organic supports are only needed to support the gear head overhang—the rest of the bracket prints support-free.

Happy meshn'!

Tagi