1 / 15
Self-Draining Shower Door Seal Trims — zdjęcie 1
1 / 15

Self-Draining Shower Door Seal Trims

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A two part Shower Door Seal that is self draining. Preventing still standing water, deposits and dirt collecting in them

Ocena
0 / 5
Polubienia
2
Pobrania
0
Wydruki
0
Wyświetlenia
65
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Bathroom
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

We have tried a number of different Seal trims for our Glass Shower doors, for both our bathrooms. They were all difficult to assemble and were quick to collect dirt, soap rests and deposits inside the trim. Partly due to that their design makes them trap standing water inside the trim.

So I made a self-draining version. It consists of two parts, a holder and a soft blade that is slid into the holder.

 The holder has individual tabs instead of a continuous trim on the inside, to enable water to run out. The surface connecting the tabs to the holder body are also sloped to make it easier for the water to run out and prevent still standing water even more.

The ends of the holder are V-shaped to make joints less visible. The holder I printed in Gravity Grey Prusament PLA, and also Galaxy Black Prusament ASA for our other shower.

 Our shower doors are curved, so I had to bend 2 holders per door to reduce the bending stress on the internal tabs. The Holders in PLA I could bend quite easy by carefully heating them up with hairdryer and pressing them against the curvature of the glass door. When they cooled down they pretty much had got the shape of the door. They can be cooled down a bit faster by changing to blowing cool air from the hair dryer.

The holders in ASA were a bit more difficult, since they have a much higher temperature resistance. So I took them out to the garage and very carefully heated them with a hot air gun. And then bent them carefully by hand, wearing gloves. But that should of course be done with the greatest of carefulness, so you don’t overheat them or burn your hands.

 The Sealing Blade has a oval shaped top that is slid into the oval shaped groove of the holder. The Blade is a couple of mm:s longer than the holder, to give an overlap between the individual Seal trim sets. And its ends is angled in 45 degrees to make these joints less visible as well. The Blade I printed in Grey TPU 95A.

I have made the Blade in a couple of different heights. Depending on the distance between the floor and the bottom edge of the shower door. I have named them by their total build height, from the underside of the shower door to the blades underside.

I recommend choosing Blades so it gives approximately 1-2 mm gap to the floor.

 I printed both the Holder and the Blade in the same position as they are mounted in. Both standing on their “two feet” on the print bed without any supports.

 The length of the Holder is adapted so that 4 pieces fits the curve length of our shower doors. Minus the vertical magnetic shower door seal. I have made two variants for our two showers.

 One for a curve length of 658 mm => each holder has a net length of 164,5 mm. And a glass thickness of 6,2 mm, which the tabs have a slight grip around.

And one for a curve length of 680 mm => each holder has a net length of 170 mm. And this is made for a glass thickness of 6,0 mm.

So if you have other lengths on your shower doors you need to scale them up or down linearly in their length direction. I can of course create more lengths if it for some reason doesn’t work to scale to a specific length.

And if your glass doors have a different thickness, you need to scale it correspondingly in its width direction in your slicer program. 

Tagi