1 / 8
Raily Keyring P1 – XIAO nRF52840 Bluetooth Button — zdjęcie 1
1 / 8

Raily Keyring P1 – XIAO nRF52840 Bluetooth Button

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Screw-together keyring case for a DIY Bluetooth button: XIAO nRF52840 Sense, DA7280 haptic, 602030 LiPo. No soldering.

Ocena
0 / 5
Polubienia
0
Pobrania
0
Wydruki
0
Wyświetlenia
5
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Raily Keyring P1 is a pocket-sized Bluetooth button you build yourself. It is the keyring for Raily, a personal AI agent that looks for people who match what you are looking for.

What it does. When someone nearby catches your eye, press the button on the side. Your phone sends the press and your location to your Raily agent, and the agent checks the people around you against your brief. The keyring itself stores nothing about you: it counts presses, blinks its LED and confirms each press with a short vibration.

Parts (no soldering)

  • Seeed Studio XIAO nRF52840 Sense (pre-soldered) on the XIAO Expansion Board

  • SparkFun Qwiic Haptic Driver DA7280 (LRA), on the board shelf

  • Adafruit Grove-to-Qwiic cable, 100 mm

  • LiPo cell 602030 (3.7 V, ~300 mAh) with a JST plug, from a seller with a UN38.3 test summary

  • 4 × M2×16 countersunk self-tapping screws (stainless), no nuts

  • Optional: 1 × 16 × 16 mm on-metal NFC sticker (ferrite backed, about 0.35–0.55 mm thick)

Outside size: 49.6 × 89.5 mm, 97.1 mm long with the loop.

Files

  • STL and STEP of every part, for any printer and slicer: cover (one flat piece), tray with key-ring loop, side-button cap, board shelf (DA7280). The key-ring loop is also a separate body (P1-tray-loop) for a second colour.

  • 3MF print profiles for Bambu Studio (Bambu Lab A1 mini, 0.4 nozzle, 0.16 mm High Quality). These are the same profiles as on our MakerWorld page.

  • The picture-by-picture assembly guide (PDF), also at devices.raily.si/build.

Print

Tested on a Bambu Lab A1 mini: 0.4 nozzle, 0.16 mm layers, PLA nozzle 220 °C, bed 65 °C, textured PEI plate. Cover, tray with key-ring loop, side-button cap and board shelf fit on one plate: about 1 h 55 min, 35 g of white PLA. Supports are needed only under the key-ring loop and under the board shelf's ledge; keep automatic supports off everywhere else. The helper STL files (…-support-enforcer, …-brim) are the support-enforcer meshes for these two places and the brims for the cap and the shelf.

Bambu Studio profiles in the files:

  • Raily-Keyring-P1-no-AMS.3mf: white PLA only, the whole set on one plate (about 1 h 55 min, 35 g).

  • Raily-Keyring-P1-profile.3mf: A1 mini + AMS lite, the whole set in white with a PETG support under the loop (about 2 h 26 min, 44 g). PETG does not stick to PLA, so the support peels off and the loop's underside comes out flat and clean.

  • Raily-Keyring-P1-2colour-profile.3mf: loop and side-button cap in a second colour (about 4 h 08 min).

  • Raily-Keyring-P1-cover-colour-profile.3mf: the cover in a second colour on its own plate.

  • white-back-violet-front, black-back-violet-front and their -loop versions: our colourways. AMS lite slots: 1 back colour PLA, 2 PETG, 4 cover colour. Violet is set in the files; Baby Blue or Blue Purple print the same.

Print the Bambu plates as they are: orientation, per-part settings, supports and seam positions are part of the files.

Assembly in short

Push the side-button cap into the hole in the tray's side wall from the inside, stem out, before the board goes in (it fits either side up; if a thin flat ring is stuck around the cap's base, peel it off). Lay the boards, the cell and the motor in the tray, put the cover on USB-C end first and drive the four self-tapping screws from the back, slowly by hand, until the heads sit flush. The full guide is in the PDF.

NFC (optional)

An on-metal sticker reads only from its printed side, so its adhesive (dark, ferrite) side must face the battery. Lay the sticker in the square pocket in the tray floor adhesive side up, peel off the liner, then put the battery in and press it down: the sticker sticks to the battery, centred over the pocket. A phone reads it through the back of the case, over the pocket.

Firmware and app

The firmware is installed by your AI agent (Claude Code, Codex or Cursor): no soldering, no toolchain. The parts list, firmware status and the Raily app are at devices.raily.si/build.

Battery safety

Use a 602030 cell from a seller with a UN38.3 test summary, check the plug polarity with a multimeter before you plug it in (sellers wire JST plugs differently), and never charge it unattended. The guide has the full list.

About the photos

The real-life photos show earlier prints of this case (two colours, the old cover with dowels). The current files are the one-plate version shown in the drawings and the plate picture.

Licence

CC BY-NC-SA 4.0: remix it and share your remix under the same licence, but please don't sell the files or prints of them. © 2026 Raily LLC. "Raily" and the Raily logo are trademarks of Raily LLC and are not covered by the licence.

Tagi