OGHom GH02 Steamer Wall Holder – Scan-Fitted J-Hook Cradle, Heat-Safe, No Drilling
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Scan-fitted wall holder for the OGHom GH02 steamer. Nothing touches the hot steam plate. VHB mount, prints on its side.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 3
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other House Equipment
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Stop leaving a hot steamer lying on the counter. This cradle gives your OGHom GH02 its own spot on the wall: drop it in when you're done, and lift it straight out when you need it.
I designed it around a 3D scan of my own GH02, so it fits the steamer's real shape instead of a guess from product photos.
Highlights
Scan-fitted. Built directly from a Shining 3D Einstar scan. The floor follows the curve of the steam head's underside, and the side walls follow its rounded ends.
Hands off the hot plate. Nothing touches the steam plate. The steamer hangs with the plate facing the wall and a 5 mm air gap behind it. The gap is open at the top and bottom, so leftover steam vents upward and drips fall straight through.
Secure without being fussy. J-hook tips behind the head, plus end walls that wrap its corners, keep it from tipping forward or swinging into the wall. The handle hangs free in front, and nothing presses the buttons on the back of the handle.
No drilling. The tall, flat back is made for VHB tape and gives roughly four times the bond area 3M recommends for this weight.
Prints strong. It prints on its side, so the layers run along the J and the steamer's weight is carried along the layers rather than across them.
Fit
Made for the OGHom GH02 handheld steamer (the 2-in-1 steamer/iron).
Hang it with the head in its normal steaming position, not swiveled 90°.
Other steamers will only fit if their head is very close to the GH02's (about 126 × 33 × 61 mm).
Print settings
Setting | Recommendation |
|---|---|
Orientation | On its side, exactly as the file is oriented |
Supports | Yes: tree/organic, allowed to start on the model |
Material | PC-CF (carbon-fiber polycarbonate). It stays stiff well above steam temperature, so you can hang the steamer up hot. Avoid PLA and PETG. |
Printer setup | Hardened steel nozzle, enclosed printer, dried filament; textured PEI or glue stick on the bed |
Layer height | 0.2 mm |
Walls / infill | 4 walls, 20–25% infill |
Size | 137 × 51 × 134 mm installed |
Mounting
Wipe the wall and the back of the print with isopropyl alcohol.
Apply 3M VHB tape across the flat back (for example 3M 5952 on painted walls).
Press firmly for 30 seconds.
Wait 24 hours before hanging the steamer.
Using it
Unplug the steamer, then lower it straight down with the steam plate facing the wall.
To take it, lift straight up and pull it toward you.
Behind the design
I modeled it parametrically in Python, working directly against the scan.
The fit was checked digitally: the steamer drops in without collisions, with about 1 mm of clearance around the head and handle.
The images are renders of the final model.
Not affiliated with or endorsed by OGHom.