1 / 10
Carmilla Mask Inspired From Castlevania Belmont's Curse — zdjęcie 1
1 / 10

Carmilla Mask Inspired From Castlevania Belmont's Curse

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Carmilla's Mask Inspired From the video game Castlemaine Belmont's Curse

Ocena
0 / 5
Polubienia
2
Pobrania
1
Wydruki
0
Wyświetlenia
11
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Masks
Licencja
Creative Commons — Attribution — Share Alike

 

Carmilla's Mask Inspired By the One in Castlevania Belmont's Curse.

 

The mask uses Basic White Pla for the mask, Red Silk+ Pla for the Blood to give it a shiny effect, black pla for the mesh.

 

The Print profiles have different sizes based on Head Circumference to ensure the best fit for your  mask, measuring your head circumference accurately is essential. Follow these steps:

1. Use a flexible measuring tape (or a piece of string if you don’t have one).
Position the tape just above your eyebrows and ears.
2. Wrap it around the back of your head at the point where your head slopes upward prominently from your neck. This is usually the widest part of your head.
3. Make sure the tape is snug but not tight, and that it stays level all around your head.
5. If you used a string, mark the length where it meets, then measure that length with a ruler or measuring tape.

 

Edit Listing image 10

Important:

Always measure the largest circumference of your head to get an accurate size.
If your measurement falls between two sizes (for example, 23.25 inches), round up to the next size (in this case, 23.5 inches).

 

 

Assembly

 

For the Head Strap I used a 1in Elastic Band often used in sewing.

 

Here Is a guide on how to loop the bands throught the loops and mask.

 

Items Required:

Carmilla Mask (Multi-Color or Multi-Part)

Mesh Inserts

1in wide Elastic Band

Tri Glide Slide Loops

 

Optional:

Hot Glue and Hot Glue Gun

 

Steps:

  1. Roll out Elastic band measuring to about 25in long and cut to size. Do this twice becuase your would need two 25in long Elastic Bands.

Optional: Use a lighter to singe the edges of the Elastic band to prevent fraying or unraveling of the elastic band.

2. Place one elastic band vertically on a flat surface. Position the second elastic band horizontally across the vertical band, approximately 5 inches from the bottom.

 

 

Fold the bottom end of the vertical band back over the horizontal band. Using a hot-glue gun, attach the folded section to the longer part of the vertical band to create a loop around the horizontal band. Make sure the horizontal band can move freely through the loop.

3.  Once the glue has dried, lay the straps flat with the glued side of the head strap facing downward and the seamless side facing upward.

 

Using the three tri-glide slide loops, thread one end of the band through the bottom opening of a slide loop. Bring it up and over the center bar, then feed it through the top opening. Pull the band tight and repeat these steps with the remaining ends. Take the mask and mesh inserts. Turn the mask inside out so the interior is facing upward.

 

 

4. Take the mask and mesh inserts. Turn the mask inside out so the interior is facing upward.

 

Place the left-eye mesh insert—the piece marked with the red circle—over the inside of the mask’s left eye opening. Position it as desired, then secure it

 using either tape, as shown in the example, or glue. If using glue, hold the insert in place until the glue has fully cured.

 

Repeat this process with the right-eye mesh insert—the solid black piece—and then attach the mouth mesh insert.

 

Note: If you printed the Carmilla mask as a single piece, disregard the upcoming second half of this step.

 

Next, turn the mask over so the front is facing upward. Apply a small amount of your preferred adhesive to the blood streak and attach it to the mask. A little glue goes a long way, so avoid using too much. Align the blood streak with the left eye; its shape should guide it into the correct position. Apply moderate pressure until the adhesive has cured.

 

5. Finally, assemble the mask and head strap. Turn the mask over so the interior is facing upward.

Place the head strap over the inside of the mask. Spread the vertical and horizontal straps out and align each one with its corresponding hook on the mask.

For each end of the elastic head strap, follow these steps:

  1. Feed the strap through the inside of the corresponding hook, bringing it out through the hook’s outer end.

  2. Loop the strap back through the inside opening of the tri-glide slide loop.

  3. Bring it over the center bar and down through the opposite opening of the slide loop.

  4. Pull the strap tight to secure it.

Repeat these steps for the remaining strap ends and mask hooks. Once all the straps are attached and adjusted, the mask assembly is complete.

 

Bring a little Castlevania: Belmont’s Curse energy to life with this Carmilla-inspired mask! With its dramatic blood detail, separate mesh inserts, and adjustable elastic head strap, this model makes a unique cosplay accessory or eye-catching display piece.

I hope you have as much fun printing and assembling it as I did creating it. Thank you to everyone in the MakerWorld community for your support, feedback, and creativity. If you make one, be sure to share your finished print. I would love to see it!

Enjoyed this model? Check out my other designs for more fun projects to print, build, and bring to life!

Carmilla

Tagi