1 / 9
SAI — Tablet Splitter & Crusher — zdjęcie 1
1 / 9

SAI — Tablet Splitter & Crusher

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Two-stage 3D-printed bench prototype with trays for halves and quarters, a crusher insert and a storage drawer.

Ocena
0 / 5
Polubienia
5
Pobrania
14
Wydruki
0
Wyświetlenia
116
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

English

SAI is a printable mechanism for experimenting with tablet splitting and crushing on inert test pieces. Close the inner lid first, then squeeze the outer cover against the base to drive the actuator. Both splitting trays fit in the drawer.

  • Halves: the T03 V-tray centres round or oblong test pieces under the printed wedge.

  • Quarters: after the first split, switch to the T07 tray and divide each half separately.

  • Crushing: fit the T10 cup and T11 pressure disc, and swap the wedge actuator T05 for the blunt actuator T12. The same outer cover presses the disc.

  • Screwless assembly: the hinges and retaining pins use cut lengths of 1.75 mm filament. Three return springs still need to be selected and tested.

Start with the filament-pin fit coupon. The STL files are supplied in trial orientations. A 0.4 mm nozzle, 0.2 mm layers, 4 walls and 5 top and bottom layers are starting settings for bench prints. Check the slicer preview for wedge detail and supports. The illustrated EN/PL guide includes the part list, pin lengths and assembly sequence.

Prototype status: the model and motion were checked in CAD. Physical cutting consistency, pin retention, spring force, wear, interlock performance and cleaning have yet to be verified. The gallery includes CAD line drawings and separate operation and assembly GIFs. Use inert test pieces only. Ask a pharmacist or check the medicine leaflet before altering any medication.

Polski

SAI to drukowany mechanizm do prób dzielenia i rozgniatania na obojętnych atrapach tabletek. Najpierw domykasz wewnętrzną osłonę, a potem ściskasz górną pokrywę z podstawą. Obie tacki mieszczą się w szufladzie pod obudową.

  • Połówki: tacka V T03 centruje okrągłe i podłużne atrapy pod drukowanym klinem.

  • Ćwiartki: po pierwszym podziale zamień tackę na T07 i podziel każdą połówkę osobno.

  • Rozgniatanie: załóż miseczkę T10 i krążek T11, a popychacz z klinem T05 zamień na tępy T12. Docisk wykonujesz tą samą pokrywą.

  • Montaż bez śrub: osie i piny to docięte odcinki filamentu 1,75 mm. Trzy sprężyny powrotne trzeba jeszcze dobrać i sprawdzić.

Zacznij od próbki pasowania pinów. Pliki STL mają ustawioną orientację do prób. Zacznij od dyszy 0,4 mm, warstwy 0,2 mm, czterech obrysów i pięciu pełnych warstw z góry oraz z dołu. W slicerze sprawdź krawędź klina i potrzebę podpór. Ilustrowana instrukcja EN/PL zawiera listę części, długości pinów i kolejność montażu.

Status prototypu: model i ruch sprawdzono w CAD. Powtarzalność cięcia, utrzymanie pinów, siła sprężyn, zużycie, skuteczność blokady i czyszczenie wymagają prób fizycznych. Galeria zawiera rysunki konturowe z CAD oraz osobne GIF-y działania i montażu. Do prób używaj wyłącznie obojętnych atrap. Możliwość dzielenia lub rozgniatania leku sprawdź w ulotce albo u farmaceuty.