Illuminated Pulse Oximeter Sensor – USB-Powered Training Dummy
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A realistic, USB-powered illuminated pulse oximeter finger clip designed for medical simulation and training. Features a
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 12
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Gadgets
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This 3D-printable model is designed as a realistic, illuminated pulse oximeter finger clip for use in medical simulation, anesthesia training, emergency medicine, tactical medicine, and other healthcare education environments.
The model replicates the appearance and basic mechanical functionality of a conventional finger-clip pulse oximeter sensor, including a flexible lower section, spring-loaded opening mechanism, connecting cable, and illuminated red LED.
The LED is powered through a standard USB connection, allowing the sensor to produce a visible red light similar to that of a real pulse oximeter probe.
This is a simulation device only. It does not measure oxygen saturation (SpO₂), pulse rate, or any other physiological parameter.
We use this type of sensor during medical simulation and training to improve the realism of patient monitoring equipment without requiring a functional clinical pulse oximeter probe.
DESIGN CREDIT
Original designer: Rostislav Orlík
Contact: [email protected]
Special thanks to Rostislav Orlík for designing and developing this practical simulation accessory.
MODEL COMPONENTS
The model consists of four 3D-printed parts:
Upper Housing – the main rigid body containing the LED and cable channel.
Lower Housing – a flexible TPU component forming the lower part of the finger clip.
LED Cover – a red protective cover for the illuminated LED.
Cable Cover – a rigid component securing the cable inside the upper housing.
In addition to the printed components, assembly requires several basic electronic and mechanical parts, including soldering, gluing, and screw installation.
REQUIRED COMPONENTS
Electronic components
3 mm red LED – forward voltage 2–3 V, nominal current 20 mA
150 Ω resistor – connected in series with the LED
USB Type-A male connector – for a 5 V DC power supply
Two-core electrical cable – 0.5 mm, approximately 3 meters long
Mechanical components
Self-tapping screws – 1.8 × 5 mm (2 pieces)
Compression spring – approximately 20 mm long, suitable for example from a ballpoint pen
Tools and additional materials
Soldering iron and solder
Cyanoacrylate (super glue)
Small screwdriver
Wire stripper or suitable cutting tool
Electrical insulation or heat-shrink tubing
Multimeter (recommended)
PRINTING RECOMMENDATIONS
The model was designed for FDM 3D printing.
Recommended nozzle diameter: 0.4 mm
Different materials are recommended for individual components to achieve the desired combination of rigidity, flexibility, and appearance.
1. Upper Housing
Material: PETG
Orientation: Upper surface facing upwards
Wall loops: 3
Infill: 15%
Supports: Manually painted
Support interface material: PLA for easier separation
Top Z support distance: 0 mm when using the PLA interface
When preparing the supports, leave the LED tunnel free from support structures to prevent obstruction of the LED installation.
Using PLA as a support interface for PETG can help achieve cleaner supported surfaces and easier support removal when compatible multi-material printing equipment is available.
2. Lower Housing
Material: TPU
Orientation: Bottom surface facing the build plate
Wall loops: 3
Infill: 15%
Supports: Not required
TPU provides flexibility and helps the lower section conform to the finger during simulation.
3. LED Cover
Material: Red PETG
Wall loops: 10
Infill: 0%
Supports: Not required
The red PETG cover provides the finishing detail for the illuminated section of the sensor.
4. Cable Cover
Material: PETG
Orientation: Flat surface facing the build plate
Wall loops: 10
Infill: 0%
Supports: Not required
This component secures the cable inside the upper housing and helps prevent accidental cable displacement.
ELECTRICAL ASSEMBLY
The electronics consist of a simple USB-powered LED circuit.
The LED must be connected to the 5 V USB power supply through a 150 Ω current-limiting resistor.
USB Connection
Prepare the USB male connector and the two-core electrical cable.
Identify the USB +5 V and ground contacts. Verify the connector pinout before soldering.
Solder the red wire to the +5 V contact.
Solder the black wire to the ground (GND) contact.
Ensure that the soldered contacts are properly insulated and cannot short-circuit.
Assemble the USB connector housing and secure it with a suitable adhesive if required.
LED Connection
Solder the 150 Ω resistor in series with the red LED.
The resistor can be connected to either the LED anode or cathode.
Connect the LED and resistor assembly to the two-core cable, observing the correct polarity.
Insulate all exposed electrical connections, particularly the two LED leads.
Test the LED using a suitable 5 V USB power source before installing it into the printed housing.
Important: Incorrect polarity may prevent the LED from illuminating. Never connect the LED directly to the USB power supply without the current-limiting resistor.
MECHANICAL ASSEMBLY
After completing and testing the electrical connections:
Insert the LED and cable assembly into the internal channel of the upper housing.
Position the LED so that it extends into the designated opening.
Make sure that the LED leads are electrically insulated from each other.
Arrange the cable inside the internal chamber to allow the cable cover to fit correctly.
Install the cable cover, ensuring that its wider curved section faces towards the LED.
Secure the cable cover using the two 1.8 × 5 mm self-tapping screws.
Verify that the cable is firmly retained and cannot easily be pulled out.
Attach the red LED cover using a small amount of cyanoacrylate glue.
Insert the compression spring into the designated recesses at the rear of the housing.
Assemble the upper and lower housing components to complete the finger clip.
After assembly, check that the spring-loaded mechanism opens and closes smoothly, the cable is securely fixed, and the LED illuminates correctly when connected to USB power.
APPLICATIONS
This model is particularly suitable for:
Anesthesia and intensive care simulation
Emergency medicine training
Tactical Combat Casualty Care (TCCC) exercises
Military medical simulation
Medical student education
Patient monitoring simulation
Simulation-based team training
The model can be used as a realistic visual accessory together with simulated patient monitors and other training equipment.
IMPORTANT SAFETY DISCLAIMER
This model is intended exclusively for educational, training, and medical simulation purposes.
It is not a certified or approved medical device, has not been clinically validated, and must not be used for actual patient monitoring, diagnostic purposes, or clinical decision-making.
The device does not measure SpO₂, pulse rate, or any physiological parameters.
The electronics are intended for a suitable 5 V DC USB power supply only. Verify the USB pinout, polarity, electrical insulation, and absence of short circuits before connecting the device to power.
Do not connect the model to clinical pulse oximeter sensor ports or other medical equipment connections unless their compatibility and electrical safety have been independently established.
The model has not undergone medical electrical safety, biocompatibility, or disinfection validation.
Regularly inspect all printed and electronic components for damage, deformation, loose connections, excessive heating, or exposed conductors.
The creator and designer assume no responsibility or liability for injury, electrical damage, equipment malfunction, adverse outcomes, or any other consequences resulting directly or indirectly from the manufacture, modification, assembly, or use of this model.
For simulation and educational purposes only. Not a certified medical device.