Tufty Cyberdeck Modular
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Two-part glue-free outer case for the Tufty 2350 in its stock case: TPU bumpers, 4-position kickstand, rear module rail.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 10
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Open Community License v1.1 + General Attribution v1
What it is
An outer protective case that goes over the Tufty 2350 already assembled in its stock case. The battery is never touched, no glue anywhere.
Front frame with 5 captive button caps
Back shell with port opening (USB-C, Qw/ST, SWD) and clip-in translucent LED diffusers
4 TPU corner bumpers, 8 replaceable TPU damper pads
Fold-flat kickstand with 4 detents (0 / 25 / 40 / 55°), replaceable detent clips
Lanyard holes
Standard rear rail (drop in, slide 10 mm down, click) with 4 modules: Multi-Sensor Stick mount, magnet mount, belt clip, small box
Parts to print
File | Qty | Material | Supports |
|---|---|---|---|
| 1 | PETG black | no |
| 1 | PETG black | no (bridges ≤ 6 mm) |
| 5 | PETG orange (or TPU) | no |
| 1 plate | translucent PETG | no |
| 1 | PETG orange | no |
| 1 plate | PETG (or POM) | no |
| 1 | PETG orange | no |
| 1 plate | TPU 95A | no (check overhangs in slicer) |
| 1 plate | TPU 95A | no |
| 1 each, optional | PETG | local support under the locking tooth |
| 1 each | PETG | see validation doc |
Hardware
Qty | Item | Use |
|---|---|---|
4 | M2×10 button head screws | frame / shell closure |
4 | M2×6 button head screws | rail plate |
8 | M2 brass heat-set inserts, 4 mm long, ≈ Ø3.5 | 4 shell + 4 rail plate |
2 | Ø2 × 12 steel pins | kickstand hinge |
2 | Ø10 × 3 neodymium magnets | magnet module (optional) |
2 | M2.5 × 6 self-tapping screws | Multi-Sensor Stick module (optional) |
1 | short 4-pin JST-SH cable | Qw/ST to sensor module (optional) |
Print the coupons first
Coupon | What it validates |
|---|---|
02 inserts (print first) | insert hole size (Ø3.0 / 3.2 / 3.4) and screw clearance holes |
01 ring | holding clearances on the badge rim, USB-C position, side pads |
04a/b top beam | PCB tab slot (must never be squeezed), lanyard windows, top screws, HOME / RESET / Qw/ST in the port opening |
03a/b bottom band + 3 button caps | A/B/C button travel and return, accidental presses, bottom screws |
05 rail (3 clearances) | dovetail fit and lock click: pick the clearance that suits your printer |
06a/b hinge + 1 detent clip + pin | pin press fit, free rotation, detents |
07 LED tunnel + 1 diffuser | diffuser clip fit |
08 datum template (0.6 mm) | real port / LED positions against the ±3 mm estimates |
Assembly
Heat-set the 8 M2 inserts (4 on the shell joint face, 4 on the shell back for the rail plate).
Push the 8 TPU pads into their pockets.
Clip the 4 diffusers in from outside.
Kickstand: detent clips into their slots, kickstand into its grooves, press the two Ø2 pins in from the sides.
Screw the rail plate (4 × M2×6).
Lay the Tufty in the back shell.
Front frame face down: drop the 5 button caps in, flange inward.
Close and fit the 4 M2×10 screws. Do not overtighten: the joint faces bottom out.
Slide on the 4 TPU bumpers.
Modules: drop in, slide 10 mm down until it clicks.