Modular Challenge Coin Display - Stands, Risers, Curves, Ring & Oval (Support-Free, P1S + 300 mm)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Modular, support-free display system for military challenge coins. Straight stands, rear risers, 45 and 22.5 degree curv
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 2
- Wydruki
- 0
- Wyświetlenia
- 20
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Office
- Licencja
- Creative Commons — Attribution
A modular stadium-style display for challenge coins. Every piece has 10 stepped rows of slots that lean coins back 12 degrees, so each row is visible over the one in front. Pieces lock together with hidden bowtie Joint Keys that slide up from underneath - no glue, no screws, nothing visible from the sides.
What you can build
Coffee-table ring - 8 identical 45 deg wedges (P1S: 20.6 in / 524 mm diameter, ~120 coins; 300 mm: 23.8 in / 604 mm, ~136 coins)
Oval coffee table - ring split in two with straight bases between (P1S: 30.5 x 20.6 in, ~215 coins; 300 mm: 35.2 x 23.8 in, ~250 coins). Extend it as long as you like.
Dresser / shelf displays - sized for a 26.75 x 15.5 in dresser top: straight (~180 coins), 22.5 deg curved ends (~130), or 45 deg curved ends (~94)
Starter stand - one base + one riser (~65 coins on P1S)
Coin counts assume coins 1.5-2.0 in (38-50 mm) across; smaller coins fit more.
Slots for thin to thick coins
Rows widen from front to back: 3.0, 3.0, 3.5, 3.5, 4.0, 4.0, 4.5, 5.0, 6.0, 7.0 mm on bases and wedges; risers add 3.5, 4.0, 5.0, 6.0, 7.0 mm. A slot holds a coin about 0.5 mm thinner than the slot. Thin coins go up front, thick ones in the back.
Parts (21 STLs)
P1S (256 mm bed): Base, Rear Riser, Wedge 45 deg L/R, Oval Spine, plus dresser-width bases/risers (223 / 234 / 149.5 mm) and Wedge 22.5 deg L/R
300 mm bed: Base, Rear Riser, Wedge 45 deg L/R, Oval Spine
Any printer: Joint Key, End Plug, Fit Test Block
Do not mix 300 mm and P1S stands in one display - their step heights differ.
Start with the Fit Test
Print 2x Fit Test Block + 1x Joint Key (about 20 minutes). If the key slides in snugly by hand, print the rest. Too tight: scale the key to 98% in X/Y. Loose: 101-102%.
Assembly
Butt pieces together, slide 2 Joint Keys up into the bowtie sockets under each seam, and press End Plugs into any exposed end. Rings and ovals use 8 wedges of the SAME hand. The full illustrated Print and Assembly Guide (PDF) with a bill of materials for every layout is included in the files
Print settings (form fields)
Printer: Bambu Lab P1S (also any 300 x 300 mm printer for the 300 parts)
Supports: No
Rafts: No
Resolution / layer height: 0.20 mm (keys 0.12-0.16 mm)
Infill: 10% gyroid for stands (Lightning saves ~40%); 100% for keys and plugs
Filament: PLA / PLA+
