1 / 5
BETAFPV Air75 II – Stiff Low-Profile Replacement Frame (PETG) updated — zdjęcie 1
1 / 5

BETAFPV Air75 II – Stiff Low-Profile Replacement Frame (PETG) updated

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Stiff, low-profile replacement frame for the BETAFPV Air75 II. The props stay centered in the ducts even after crash

Ocena
0 / 5
Polubienia
1
Pobrania
5
Wydruki
2
Wyświetlenia
33
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution — Share Alike

The BETAFPV Air75 II is a great little whoop, but its stock polypropylene frame is too soft. After a few crashes the prop guards aren’t round anymore. The props start to scrape, the motors tilt and the quad gets noisy.

I designed this frame from scratch to fix that.

What’s different

  • Stiff ducts. Each duct is held by 6 spokes running directly from the motor mount to the rim, so the rim stays centered on the motor axis and the prop clearance stays constant.

  • Low profile. The FC sits flush with the top of the ducts, and the camera is mounted between the front ducts instead of on a tall canopy. Nothing sticks out above the frame except the antenna.

  • Battery on its side. It sits in a tunnel between the ducts along the centerline, inside the frame footprint, with a clip so it can’t slide out.

  • Protected camera. The lens sits behind the front edge of the ducts, so the ducts take frontal hits.

  • Bumper tabs on the rim where each spoke meets it, so side hits land on a spoke instead of the middle of the rim.

  • Wire routing along the spokes to the FC, so no loose motor wires hang near the props.

Compatibility

  • BETAFPV Air75 II stock electronics: 0802 motors (3 × M1.4, 6.6 mm bolt circle), 25.5 × 25.5 mm AIO FC (mounted rotated 45°), C03 camera

  • Props: Gemfan 1614 3-blade (40 mm)

  • Battery: 1S, approx. 10 × 6.5 × 64 mm (tested with Tattu 1S 300 mAh HV, BT2.0)

Weight

  • This frame: ~8.3 g in PETG also added TPU holder for antenna and camera

  • Stock frame: 4 g + Cannopy

It’s heavier than stock, but it doesn’t bend. In my tests it flies quieter and more stable, and it survived repeated drops that would deform the stock frame.

Print settings

  • Material: PETG (tested; clear/natural PETG prints cleanest). PLA is not recommended, it’s too brittle and softens from motor heat.

  • Layer height: 0.2 mm

  • Walls: 4, infill irrelevant (all parts are thin walls)

  • Seam: Aligned

  • Orientation: rims down on the bed

  • Supports: tree, top Z distance 0.2–0.3 mm

  • Brim: 3–4 mm on the rims

  • Clean the bed and use a glue stick for good adhesion

Hardware

  • Stock motor screws (M1.4)

  • 4 × M1.4 self-tapping screws for the FC

  • Optional: 2–3 mm TPU feet under the motor mounts

Tips

  • Every PETG brand behaves a bit differently. Tune temperature and retraction per filament to avoid stringing.

  • After printing, check that the motor seats are flat before mounting the motors.

  • Recalibrate the accelerometer in Betaflight after swapping frames.

Tagi