1 / 1
Ambush NM (Official) - CI Genesis / Reaper Breakout Card Handles — zdjęcie 1

Ambush NM (Official) - CI Genesis / Reaper Breakout Card Handles

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

44 Delta handles for CI Genesis and Reaper Breakout Card picks. All-printed and Chicago screw versions. No magnets.

Ocena
0 / 5
Polubienia
0
Pobrania
2
Wydruki
0
Wyświetlenia
20
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial

Ambush NM handles are designed specifically for the metal picks from the Covert Instruments Genesis Breakout Card and Reaper Breakout Card. These are the credit-card-sized, snap-out tools pictured above—not the regular Genesis or Reaper pick sets.

44 Delta is proud to share Ambush NM for you to print at home. NM means no magnets. The handles add a comfortable grip to these small picks and can hold one pick or two pointing in opposite directions. Choose a fully printed sliding-lid version or a version fastened with Chicago screws.

This is an original 44 Delta design. Ambush NM is not currently sold as a finished product by 44 Delta. If you enjoy the design, please credit 44 Delta, share a make, and visit 44delta.com to see more of my locksport work.

Compatibility

  • Covert Instruments Genesis Breakout Card

  • Covert Instruments Reaper Breakout Card

The handles accommodate the different pick-handle profiles and hole spacing of these two cards. The metal picks are separate items and are not included in these print files. “Official” refers to this being the original 44 Delta model release. 44 Delta has no affiliation with Covert Instruments.

Project File Organization

  • Ambush NM - All 3DP: Handle and Lid STLs, plus One Color and Two Color 3MF projects. For one complete handle, print one Handle and two Lids. No screws or magnets are required.

  • Ambush NM - Chicago Screws: Upper and Lower STLs, plus One Color and Two Color 3MF projects. Print one Upper and one Lower per handle. These are different mating halves.

  • Ambush NM - Complete Project: All.3mf, containing the combined project.

  • Instructions: Ambush-NM-Assembly-and-Disassembly.pdf. This illustrated, black-and-white-friendly guide has a separate page for each version.

Hardware — Chicago Screw Version Only

Use uxcell brass Chicago screws, 3×8 mm option (Amazon). The referenced size has an 8 mm head diameter, a 3 mm post length, and a 7 mm overall assembled height. Do not confuse the 3×8 mm option with an 8 mm-long post. Use two complete screw-and-barrel sets per installed pick, or four sets for a double-ended handle. You will also need a suitable flat-blade screwdriver.

Assembly & Disassembly — All 3DP

  1. Place the pick in its pocket and seat its rear hole fully down on the retaining peg.

  2. Align both dovetails before sliding the lid on from the tip toward the middle. If the lid becomes too tight, stop and check that the dovetails are aligned and the rear of the pick is fully seated on its peg.

  3. Some resistance is expected when the lid is nearly all the way on, just before it latches. Check that the seated lid is retained.

  4. To remove the lid, insert a small release tool through the access hole on the opposite face. A thin, low-profile hook can serve as the tool. Push through the hole at the same time you slide the lid back toward the tip. Keep the catch released until it clears; do not force or pry the lid off.

Assembly & Disassembly — Chicago Screws

Seat the picks in their pockets, align the two halves, and pass the hardware through the mounting slots and pick holes. Start all screws loosely, then tighten evenly until the picks are held securely. Hold the barrels if they turn, and avoid overtightening the printed parts. To disassemble, hold each barrel while loosening its screw, remove the hardware, and separate the halves. See the included PDF for illustrations.

Printing

  • PLA and a 0.4 mm nozzle were used during development.

  • Use the supplied 3MF projects to preserve the prepared part placement and color assignments. Select your own printer and filament profiles before slicing; the saved projects target a Bambu Lab H3C.

  • The supplied projects use 0.12 mm nominal layers and 15% infill. Check the layer preview around the dovetails, latch, and screw recesses before printing.

  • Chicago screw version: use supports for the counterbores (the recessed screw-head pockets). Enable these supports in your slicer before printing, including when using the supplied 3MF projects.

  • Print lids on their flat outer faces. Keep mating surfaces clean and remove any brim or first-layer lip that interferes with assembly.

  • Use the Two Color projects for contrasting 44 Delta branding. Keep the logo parts registered with their parent parts rather than arranging them as separate objects.

License & Credit

Shared under Creative Commons Attribution–NonCommercial 4.0. Please credit 44 Delta and link to this model when sharing or remixing. Commercial use is not permitted under this license.

Tagi