Coralboard Clamshell: Ported Case + Vesa 75/100 Adapter
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A two-part printable case for the Synaptics Coralboard, plus an optional VESA plate.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 11
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Creative Commons — Public Domain
What you get
File | What it is | Print orientation |
|---|---|---|
| Tray with 4 standoffs, wall cut-outs, 2 wall-mount keyholes | floor on the bed |
| Lid with 4 clamp posts, SoC vent grille, GPIO / camera windows | upside down, flat top on the bed |
| Optional adapter, VESA MIS-D 75 and 100 | flat |
Assembled: 79.8 x 65.8 x 19.3 mm (23.3 mm on the plate). Plate: 112 x 112 x 4 mm.
Design
One fastener set does everything. Four M3 countersunk screws go up from the underside, through the base standoffs and the board's own 65 x 48 mm mounting holes, and thread into the lid posts. That clamps base, board and lid together. No glue, no snaps, nothing to break.
Every connector has a path out. Cut-outs are sized from the connector bodies in the reference STEP model, with clearance for plug overmolds:
Front: 4-pin JST (Qwiic or I3C) and USB-A host in one slot, USB-C (5 V power and data), and two holes for the reset and user buttons.
Left: microSD. The M.2 E-key slot sits on this edge, but a card lies flat inside the case and inserts along the board, so nothing needs to pass through the wall.
Right: the 7-pin JST (the I2S2 audio connector) and the battery connector, which also has a lid window above it in case it is top-entry.
Underside: a slot through the floor lets the ribbon of the underside FPC connector leave the case. The plate has a matching slot.
Open from above where you need it. Four lid windows cover the two 1x8 mikroBUS headers plus the CSI camera ribbon connector, the 2x2 header, the 2x10 GPIO header, and the battery connector. The ceiling sits 8.5 mm above the PCB, exactly the height of the tallest header, so Dupont plugs and a ribbon go straight up through the windows.
Airflow over the SoC. Six slots sit over the 28 x 28 mm package. The ceiling leaves about 6.8 mm above the SoC's thermal pad for a small passive heat sink.
Wall mounting. Two keyholes (60.4 mm apart) are cut through the floor. The screw heads sit in the 4 mm gap under the board. Hang it with the USB side down.
Lap joint. The lid skirt wraps the outside of the base wall, so nothing inside the case can collide with an alignment lip. The same notches are cut through both halves.
Plate. The same four M3 holes mean the plate is just a longer screw. The VESA holes sit outside the case footprint, so you can reach the screw heads with the case on.
Exploded view
Hardware (not printed)
Qty | Part | Notes |
|---|---|---|
4 | M3 countersunk (flat head, DIN 7991) screw, 16 mm | case only. Use 20 mm if you add the VESA plate |
2 | Wall screws, head up to 8 mm dia and 3.5 mm tall, shank up to 4 mm | wall mounting only |
4 | M4 screws | VESA only. Length is 1.5 mm (plate material under the head) plus your display's thread depth, typically M4 x 8 to 10 |
The screws thread directly into the printed lid posts (2.6 mm pilot hole, about 7 mm engagement). No inserts are needed. Don't over-tighten: stop when the board is gripped.
Assembly
Drop the board onto the standoffs. The four mounting holes locate it.
Place the lid on top, skirt over the base wall. The posts land on the PCB around the holes.
Turn it over and drive the four M3 screws up through the floor. Keep the heads flush.
Optional: put the plate under the case and use the 20 mm screws, with the plate's countersinks facing down.
Board seated in the base
Print settings
PLA or PETG. 0.2 mm layers, 3 or more perimeters, 15 to 20 % infill, no supports for the plate or the lid. In the base, the cut-outs bridge up to 16.8 mm wide (the microSD slot is the widest) and the USB-A / JST notch is open at the top. Enable bridging settings, or add support blockers if your printer sags.
All geometry comes from the supplied Synaptics_CoralBoard_SL.step. I built three checks against it:
Meshes: all three STLs are watertight (every edge shared by exactly two triangles).
No collisions: every one of the 176 solid bodies in the STEP model, sampled over its bounding box, was tested against the base and lid. Result: 0 interferences. Datasheet reconciliation changed the design: closed the unneeded M.2 wall cutout, added the battery window and the floor ribbon slot. The tightest real gap is 0.2 mm (the rubber bumper under the board at its back-left corner). The SoC corner clears the front-right lid post by 0.2 mm.
Ports open: from each connector's face I swept 15 mm outward through the wall. All 11 connector paths are free, and the assumed M.2 card envelope is clear.
Not printed or test-fit. This was checked against the CAD model only, not against a physical board. Allow for real-world tolerance.
Matched to the datasheet by inference. I matched part numbers to the datasheet's connector list by size and position, not from a labelled drawing. The M.2 slot, the battery connector (JST-PH) and the I2S2 7-pin are fairly certain. Which 4-pin connector is Qwiic and which is I3C is not. I couldn't tell whether the battery connector is top- or side-entry, so it has both a window and a wall slot.
Underside FPC: I assumed it is the display connector and that the ribbon leaves through the floor slot. I couldn't tell which way it opens. Wall mounting or the plate over the slot would block the ribbon, so leave the plate off in that case.
M.2 card clearance is checked against an assumed envelope for a 2230 card (22 x 30 mm, up to 6.5 mm above the PCB). It clears with 1.4 mm to spare. Check it against your actual module.
Test points are on the underside (the datasheet says so), and the floor covers them. If you need them for power measurement, widen the floor slot.
LEDs: the three status LEDs are under the lid. I didn't add light holes.
Large plugs may not fit. The USB-C slot is 12 x 7 mm and the USB-A slot is wider. Plugs with big overmolds may need the slot widened.
The two buttons have 4.4 mm holes; you need a pin or pen tip to press them. I don't know what they do, so they aren't labelled.
Clearances are bounding-box based. They are conservative for rectangular parts, but small SMD parts near the posts were checked only by their boxes.
Mesh resolution: meshed at 0.25 mm, so sharp edges are softened by about 0.1 mm. Flat faces and hole positions are exact.
