Shearwater Swift & Swift GPS Transmitter Bumper
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Full-cover TPU bumper for the Shearwater Swift transmitter, plain or with a green GPS badge inlaid in the top.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 1
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor Sports
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
A one-piece TPU bumper that covers the whole Shearwater Swift transmitter, top and sides, and leaves only the bottom open for the HP port. It goes on from the top: the Swift slides in through the open bottom until eight tongues click under the metal ring at the base of the transmitter. A Ø 9 mm window sits over the status LED.
Two versions in one project: plain, and GPS with a signal icon and the letters GPS in green TPU inlaid flush in the top, along an arc. Handy when you run more than one Swift and want to see at a glance which one is the GPS one.
Made for the Shearwater Swift and Swift GPS, which Shearwater lists at the same size (76 × 34 mm, 135 g).
Print-tested: I printed both versions in black and green TPU for AMS and fitted them on my two transmitters, a Swift and a Swift GPS, on the regulator (see photos). Not dive-tested yet, and I have not checked the drainage in water yet.
Ø 39.3 × 64.0 mm outside, wall 2.94 mm (7 lines). Inside the base Ø 33.42 mm: my Swift measures 106 mm around (Ø 33.7 mm), and I make TPU sleeves 1 mm shorter around for a light stretch
Above the base the inside follows the shape of the Swift's cap (the raised arch with the screw, the side wing and the LED fin) closely, so the bumper cannot turn on the transmitter. The cap shape comes from photos and measurements of my Swift and was tightened by 0.3 mm per side after a printed test piece
Grip: 8 tongues (1 mm slits, 14.6 mm long) with 2.2 mm hooks that click under the metal ring: 45° lead-in, 35° holding face with 0.3 mm preload that pulls the bumper down onto the cap. An earlier version with 11.6 mm slits was too stiff to put on and broke its hooks
Drainage: the LED window, a 0.6 mm gap above the cap and 4 channels (2 × 1 mm) along the inside of the wall down to the open bottom
Put it on slowly: the tongues bend across the print layers, and Bambu's datasheet gives TPU for AMS only 31 % elongation across layers (over 650 % along them)
GPS version: signal icon and GPS in Inter Black (SIL Open Font License), 9.6 mm, inlaid 0.68 mm deep (the first 4 layers) and flush with the top
Prints top down without supports: the top edge is rounded R3 and turns into 45° at the plate, so the first layers do not hang; R1.5 at the bottom. All wall thicknesses are multiples of the 0.42 mm line width. Exact CAD (B-rep) with real fillets, no stepped mesh
Both bumpers on one plate (the way I printed them): 3 h 28 min and 47.3 g on a P2S at 0.16 mm (slicer estimate; 46.6 g black, 0.7 g green, 5 filament changes)
Print settings: Bambu Lab P2S, 0.4 mm nozzle, 0.16 mm High Quality, 2 walls, 15% infill, no supports, smooth PEI plate (the top takes the plate's finish). Filament 1 is the body in Bambu TPU for AMS (black), filament 2 the GPS badge in TPU for AMS (green).
Files: 3MF (Bambu Studio project, P2S 0.16 profile, two filaments; plate 1 the GPS version, plate 2 the plain one), STL for the plain bumper and for the GPS body and lettering (already flipped for printing), STEP for both versions (GPS body and lettering as separate solids).
Photos: my prints on my Swift and Swift GPS on the regulator, the GPS top, the side with the tongues under the metal ring, the plain top, and on the hose. Render: the inside from below (tongues, hooks and drain channels).
