Fishing line spooler (for 600-660yd spools)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Wstępna wycena dla PETG
5,32 € – 6,51 € netto (bez VAT)
Dla pliku: Line-spooler-FINAL_0.2mm_PETG_MK3S_5h56m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 5,92 € netto (środek widełek).
- Masa podana przez autora
- 79 g
- Czas druku podany przez autora
- 5,93 godz.
- Materiał u źródła
- PET
- Materiał wyceny
- PETG
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
A solid, versatile way to string fishing line on fishing rods — under the necessary tension — for around $10.
- Ocena
- 5 / 5
- Polubienia
- 88
- Pobrania
- 362
- Wydruki
- 1
- Wyświetlenia
- 4150
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor Sports
- Licencja
- Creative Commons — Attribution — Noncommercial
09/17/22 update: If the wingnut continues to loosen when the spool spins, you can rotate the base 180% and flip the fishing line spool 180%. Or you can add an extra jam nut before screwing on the wing nut.
After overpaying for 200yd spools for nearly a decade, I finally spent the money and bought my first 600yd spool of fishing line. Bespoke spoolers on Amazon and Tackle Warehouse either look ridiculous or are $50-150 so I decided to design my own.
The top part is my design. Most of the hardware can be found at Home Depot. The clamp is HD_Creator's Table clamp for miniature vice 3.0 => 100% printed model.
Print notes:
- Printed with Prusament PETG
- 0.4mm nozzle at 0.2mm Quality layer height/print setting
- Perimeters: 3 for hexagonal base, 2 for axle and spacer
- Infill: 70% rectilinear for hexagonal base, 20% rectilinear for axle and spacer
- Supports everywhere (see screenshot for slightly modified “bobstro's support settings”)
- I tried printing the hexagonal base flipped on its side 90* for added strength, but two of the hexagonal sides warped and I could not prevent it. Printing the model right-side-up looks better and has not broken.
- Print the table clamp using the provided model settings
Build of Materials:
- 5/16 in.-18 x 4-1/2 in. Zinc Plated Carriage Bolt (Qty: 1)
- 5/16 in. Stainless Steel Flat Washer (Qty: 1)
- 5/16 in.-18 Zinc Plated Jam Nut (Qty: 1)
- 1 in. x 0.406-0.687 in. x 0.041 in. Cone Compression Spring (Qty: 1)
- 5/16 in. x 1-1/4 in. Stainless Steel Fender Washer (Qty: 3)
- 5/16 in. 18 Zinc Plated Wing Nut (Qty: 1)
- M3 (3mm) x 0.5 Zinc-plated Steel Hex Nut (Qty: 3)
- M3 x 12mm Thread 304 Hex Socket Head Cap Screw Bolt (Qty: 3)
- Small rectangle of foam shelf gripper/liner (optional)
BOM notes:
- Zinc-plated hardware should be fine for indoor use; upgrade to stainless steel if the spooler will be used outdoors.
- The M3 bolts and nuts are identical to the hardware that comes with the Prusa MK3S+ kit and spare parts bundle.
- You can find the 5/16-in. hardware at Home Depot, Lowes and other hardware stores. However, I could only find the cone compression spring at Home Depot.
Assembly notes:
- Attach the hexagonal base to the clamp — in any of the 8 orientations — before sliding the spool onto the axle.
- See photo with all the hardware laid out. Insert carrier bolt into printed hexagonal spooler and affix each piece in the order and orientation shown from left to right.
- If you do not follow the specific order shown, the wing nut will likely loosen when the spool spins. Update: see note atop the Description.
- Tightening the wing nut will increase tension on the spool.