1 / 6
BTT SKR V1.4, SKR V2.0, SKR 3 Case/Mount for Prusa and Bear Frame (V2.2) — zdjęcie 1
1 / 6

BTT SKR V1.4, SKR V2.0, SKR 3 Case/Mount for Prusa and Bear Frame (V2.2)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Case for mounting a Big Tree Tech SKR 1.4/2/3 to a Prusa style frame aswell as the Bear Upgrade

Ocena
4,5 / 5
Polubienia
39
Pobrania
447
Wydruki
2
Wyświetlenia
3072
Oceny
2

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

Purpose

Allows mounting of a BIGTREETECH SKR 2, SKR 1.4 or SKR 3 onto a Prusa style stock frame or mounting onto the Bear upgrade using the included base mounts.

Design

Remixed from: https://www.thingiverse.com/thing:4723441
Changed clamps, clamping method modified, size of hotend wire hole, hole mounting for frame and changed from regular nut for closing the lid to a M3nS type nut.

Design was modified in Fusion 360. Included is a STEP file for each mainboard's case if you would like to make further modifications.

(Images show V2.0 of the case, on a Bear Frame with an SKR 2. Very little has changed from V2.0 to V2.1 and V2.1 to V2.2 cosmetically, and there is little difference between the SKR 1.4, 2 and 3 cases.)

Features

  • Compatible with BTT SKR V1.4, SKR V2.0 and SKR 3.
  • Compatible and tested with Prusa/Bear Frames. See "Requirements" below to know what you'll need for the different frames.
  • Includes all cut-outs necessary for using the unit with no Wi-Fi module.
  • Prusa-style mounting onto stock frame with rotation and clips. Hole is on back of base to allow tightening of top screw.
  • Includes Prusa-style hinges for easy access of opening door.
  • Includes Prusa-style clamps for heatbed and hotend wires. 
  • Includes Bear-style base mounts for mounting onto frame.
  • Cut-out for X axis cable.
  • Bottom is open.

Changes since V1

  • Number of vents increased on door and base.
  • Prusa-like first layer time saving methods introduced on door and base.
  • Bear compatible! (please read requirements for printed parts).
  • Mounting onto stock frame brought into line with how Prusa does it.
  • No more supports required for printing.
  • Captive nut holes on the base side of the bed clamp have been improved.
  • Screw to hold door closed now sits flush with the door.
  • Captive M3nS nut to hold door closed has had it's hole shrunk to prevent it from falling out during maintenance.
  • Bed clamp has been redesigned so screws have a flat mounting point.

Changes since V2.0

  • Heatbed cable clamp copied from Original Prusa Einsy case. Now holds onto the heatbed wires stronger, and has a better mount for clamp.
  • Captive M3nS nut to hold door closed has had it's hole shrunk further.
  • Modified position of extruder cable clamp point, to allow better fitment with a 5th stepper driver.
  • Support added for SKR 1.4 and SKR 3. (Thanks to foxylaura for informing me about compatibility with SKR 3!).

Changes since V2.1

  • Discovered that the case was in fact not MK2 Frame compatible. New door added to add compatibility.
  • Door modified slightly to improve fitment with the clamps.

Requirements

  • Prusa MK2 Frame:
    • 3D Prints: [Pick one of: BaseSKR1.4, BaseSKR2, BaseSKR3], CableClamp_Bed, CableClamp_Extruder, Door_MK2, Hinge_Bottom, Hinge_Top
    • x4 M3n Nuts
    • x5 M3nS Nuts
    • x8 M3x10 Bolts
    • x1 M3x20 Bolt
  • Prusa MK3 Frame:
    • 3D Prints: [Pick one of: BaseSKR1.4, BaseSKR2, BaseSKR3], CableClamp_Bed, CableClamp_Extruder, Door_MK3_or_BEAR, Hinge_Bottom, Hinge_Top
    • x4 M3n Nuts
    • x5 M3nS Nuts
    • x8 M3x10 Bolts
    • x1 M3x16 Bolt
  • Bear Frame:
    • 3D Prints: [Pick one of: BaseSKR1.4, BaseSKR2, BaseSKR3], CableClamp_Bed, CableClamp_Extruder, Door_MK3_or_BEAR, Bear_Base_Mount_Lower, Bear_Base_Mount_Upper (Plus rambo_hinge_lower, rambo_hinge_upper from official bear project found here)
    • x4 M3n Nuts
    • x5 M3nS Nuts
    • x6 M3x10 Bolts
    • x2 M3x14 Bolts
    • x1 M3x16 Bolt

Recommended Print Settings

  • Use PETG or other high temp filament.
  • Use 0.2mm SPEED preset in PrusaSlicer.

Important Notes

If you're doing the bear modification from a MK2, you shouldn't use the MK2 door, use Door_MK3_or_BEAR.

From my testing a fan to cool the electronics was not required. I have large heatsinks on my TMC2209s and I run the motors at a low current. Please note, I have no idea how well it may preform long term in an enclosure without a fan, so please use here at own risk. I also have a small heatsink on the ARM Processor, not necessary, but I find it helps it keep that much cooler over longer prints.

Tagi