Fidget Gears Revolving V2 Print-in-Place
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Maybe that saves some lives against corona: Corona Hook Thanks for all the 45 successful makes reported on thingyverse!
- Ocena
- 3,833 / 5
- Polubienia
- 68
- Pobrania
- 625
- Wydruki
- 9
- Wyświetlenia
- 4386
- Oceny
- 6
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution — Noncommercial
Maybe that saves some lives against corona: Corona Hook
Thanks for all the 45 successful makes reported on thingyverse! Appreciated! Let's see how many prusa-community makes.
If you like my design and want to support me, please leave a Tip :)
Update 2020-Feb-09: Want to make something cool? Have a look at my SpiderBot :)
Update 2019-07-21 extended the post print description section.
After all the updates to my Anycubic I3 Mega-S printer I'm now able to print this at 100% size!
Updates on Printer were: TMC2208 Steppers, Marlin 1.1.9 Firmware, new part cooling.
Important parameter for print quality is "Outer walls before Inner walls"
Update 2019-05-06: have a look at the Remix for 5 gears (to do motor cycling games) https://www.thingiverse.com/thing:3609281
Update 2019-04-26: have a look at the Remix for keychain: https://www.thingiverse.com/thing:3584811
pdate 2019-04-22: added singulated disassembled V7 version. see description below.
Update 2019-04-16: added Print-in-Place HighRes V8E. Successfully tested on Silver ABS from Inofil3D. see comments on used settings.
In case the vertical gears are a little bit too tight (when using ABS) you could put one drop Nail Polish Remover on each Holder-Side and rotate until it's free, Then wash it out using Water. I then used Silicon Oil and it turns freely. V8E has 1mm less distance between big gears and changed the Gear-Twist to be in line with outer gear. Vertical gear moved further to the outside on that design.
Update2019-03-29: added new Print-In-Place HighRes files V7C, successfully tested on Dark-Gold PLA from ICE (assumed worst case)
Used following settings 0.6mm nozzle, 0.15mm layer height, adaptive layers (max Var 0.1, step size 0.01), concentric support, 20% infill, 60% Skin Overlap Percentage, 25mm/s outer wall speed, Print Acceleration 300mm/s², 40s min Layer Time, 100% Fan cooling, Support Overhang angle 85°, 30% Support.
If you really really like the design, use the tip the designer button ;)
After trying several versions, I have two main versions:
Print-In-Place:
Use V8E version. it has gears better to print plus optimized Holder.
- Print the stl:
-I use 0.6mm nozzle to have good print. 0.4mm is reported working from other makes.
-Concentric Support, 50%, 0mm Z-Distance
-100% infil (you'll need the stability)
-Slow Wall-Speed (20mm/s).
-Optimize your print temperature: If you print too hot, the gears get relics, if you print too cold, the Layers have not enough adhesion.
-Use print cooling, otherwise the material melts back to a "Blob" or sticks together because of being too soft when putting next layer on.
Printed with PLA and ABS. Remove Print Relics
-break off support, make sure the Gear-support removal dosn't break the gears.
In case of ABS glue them back on with Acetone.
-I use a scalpel to disjunct.
-If you don't make it with "V8E", use "V8E with Basic Supports" and find your own optimum support structure. I used intentionally a bit more sticky support, as the vertical gear easily flips over when printing (3/4 prints fail there).
Singulated:
Use V7_Singulated.zip in case your Printer doesn't manage the Print-In-Place.Print All files from the ZIP file 1x, Shaft once again.
- Cut-off the print relics (e.g. elephants foot)
- Put the big gears to the holder with Big-Radius.
- Make sure the big gears rotate freely on the holder. Use a scalpel or so to fine tune tolerances if needed for your printer
- make sure the small-gear holes and the Shafts fit together, rotating freely, pull the shaft out again
- Insert the small gears to the assembly. They fit only into one Gear. If the teeth don't dive in, it's the wrong gear.
- Put the holder with the small-radius on top.
- Rotate the Big Gear until you find the hole in the holder aligned with the holes in the gear.
- Put the shaft into the assembly. Make sure holes still align. Push with e.g. mini-torx-screwdriver (flat edge!)
- Repeat with the other gear
Enjoy playing.
Post a make or leave a note if you like this design!My first version of me was adding Balls.
Now I added a gear instead, as I mostly played with the "hole fillers"
I wanted them to revolve the gears and finally rotate the other ball.Be careful not to break off the Holders when blocking the gear (to see how strong they are). Sneak-Preview: NOT that strong.
Print instructions
Category: Toy & Game Accessories Print Settings
Printer Brand: Ultimaker
Printer: Ultimaker 2
Rafts: No
Supports: Yes
Resolution: 0.15mm
Infill: 100%
Filament: Innofil3D ABS Silver/Green/Black
Notes:
Printed with 0.6mm nozzle.
I used supports for the Holders, No support for the gears.
Very first version was pinted in Tough PLA, works as well, but my ABS is smoother.
Post-Printing
The Print Relics
Clean the Print
Not only remove the Support barrels, but also make sure the surface of the print is smoothed, otherwise it will "stutter"
Using a scalpel or a drilling machine with a 1mm drill is working good.
This smoothing process sometimes takes me 45min.
Turn the gears and see where it still sticks--> these places were overlooked.
This is much more important on PLA than on ABS, because ABS smoothed itself a bit via the Forces during play.
Post cleaning