Adjustable Headbands for the Prusa V3 Covid19 Face Shield
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
0,55 € – 0,67 € netto (bez VAT)
Dla pliku: covid19_adjustable_headbands.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 0,61 € netto (środek widełek).
- Masa podana przez autora
- 6 g
- Czas druku podany przez autora
- 41,4 min
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
I have included my project files for each of these, but you are welcome to use and/or change them in any way you’d…
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 294
- Wydruki
- 0
- Wyświetlenia
- 1478
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Ideas
- Licencja
- Creative Commons — Attribution
I have included my project files for each of these, but you are welcome to use and/or change them in any way you’d like. All I ask is that if you redistribute them, please mention me as the original creator. If you decide to sell them, please consider a charitable contribution of 10% to Cornerstone Church at https://cornerstonemi.ccbchurch.com/goto/giving
All of my files are based on my MK3S / MMU2S with a textured bed plate. As with all prints, you may want to adjust the settings to better match your setup.
Print instructions
Instructions for printing and assembling the adjustable headbands for the Prusa V3 Face Shield
I have included my project files for each of these, but you are welcome to use and/or change them in any way you’d like. All I ask is that if you redistribute them, please mention me as the original creator. If you decide to sell them, please consider a charitable contribution of 10% to Cornerstone Church at https://cornerstonemi.ccbchurch.com/goto/giving
All of my files are based on my MK3S / MMU2S with a textured bed plate. As with all prints, you may want to adjust the settings to better match your setup.
Printing the adjustable headbands and clip:
These are the 3 parts for the adjustable headband. 1 ea. male and female band and 1 retainer clip. See the Parts.jpg picture
I’ve used PLA so far with great results, but I would think PET would work even better. For the bands, I print them at .15mm layer height using the default Generic PLA profile. Once I start the print, I set my print speed to 135%. For the retainer clip I use the .3mm draft profile, also at 135% speed (set on the printer).
To assemble the parts, slide one of the bands over the tab for the elastic headband as shown in the Band Install 1.jpg picture.
You will need to flex the printed headband slightly to get it to snap over the tab. I intentionally made the hole for the tab small so that it won’t move too much after assembly. Once you’ve snapped the band in place it should look like the Band Install 2.jpg picture.
Next, rotate the band so that it extends out from the Prusa band. This requires a little bit of force, and again, this is intentional to prevent unwanted movement after assembly. The band will flex quite a bit when you do this. See Band Install 3.jpg and Band Install 4.jpg pictures.
Install the other band in the same manner. Your face shield should look like the Adjustable Bands Installed.jpg picture.
Slide the retainer clip over one of the bands – it doesn’t matter which. See the Clip Installed.jpg picture
Snap the headband together and slide the retainer clip over the snaps. See the Retainer Clip.jpg picture.
To complete the face shield, follow the instructions from Prusa at https://www.prusa3d.com/covid19/