Mini Knarre / Ratsche 1/4" Vierkant ***Print in Place***
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Mini ratchet 1/4" square ***Print in Place***
- Ocena
- 0 / 5
- Polubienia
- 67
- Pobrania
- 180
- Wydruki
- 2
- Wyświetlenia
- 1509
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Mini Knarre / Ratsche 1/4" Vierkant ***Print in Place***
+ ein Adapter 1/4" Vierkant auf 3/8" Vierkant
Eine kleine “Knarre” zum antreiben von ¼" Vierkant Werkzeugen, sehr klein gut für einen Schlüsselanhänger. (Maße ca. 51 x 20 x 6 mm )
Die Drehrichtung wird durch hin durchschieben des ¼" 4-Kants geändert.
beim 3/8" 4-Kant wird die Drehrichtung durch wechsel der Einsteck-Seite geändert, das Werkzeug dreht sich immer in Pfeilrichtung.
Bei der Positionierung auf dem Druck-Bett darauf achten das die erhabenen Pfeile nach oben weisen und die Schrift richtig herum (nicht über Kopf) steht.
Für den Druck empfehle ich PC, PETG, PLA oder ABS (ABS ist vielleicht etwas zu weich und PLA könnte zu brüchig sein.)
Es sollte mit mindestens 30% Füllung, besser 100% gedruckt werden.
Die Vierkant-Einsätze dürfen nicht in der Knarre gedruckt werden!
Diese Knarre / Ratsche erhebt nicht den Anspruch sicherheitsrelevante Schlauben mit dem vorgeschriebenen Drehmoment anzuziehen, sie ist für einfache Verbindungen im Hobby-Bereich gedacht.
Mögliche Einsatzbereiche:
Camping, Modellbau, Hobby
Für alle bei denen “Print in Place” nicht funktioniert hab ich die Teile Aussen und Zentrum nochmal einzeln beigefügt.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Google translates:
Mini ratchet 1/4" square ***Print in Place***
+ an adapter 1/4" square to 3/8" square
A small "ratchet" for driving ¼" square tools, very small and good for a key ring. (Dimensions approx. 51 x 20 x 6 mm)
The direction of rotation is changed by pushing through the ¼" 4-edge.
at 3/8" 4-
Kant, the direction of rotation is changed by changing the insertion side, the tool always rotates in the direction of the arrow.
When positioning on the printing bed, make sure that the raised arrows point upwards and that the writing is the right way round (not upside down).
For printing I recommend PC, PETG,
PLA or ABS (ABS might be a bit too soft and PLA might be too brittle.)
It should be printed with at least 30% fill, better 100%.
The square inserts must not be printed in the ratchet!
This ratchet / ratchet does not claim to tighten safety-related loops with the prescribed torque, it is intended for simple connections in the hobby area.
Possible areas of application:
Camping, model making, hobbies
For everyone where "Print in Place" doesn't work, I've attached the parts outside and center again individually.