Topcon UV Topcor Lens To Sony A7II-series Body Adapter
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Topcon is a highly respected Japanese optical company now known for opthalmic equipment, but for a while they made…
- Ocena
- 0 / 5
- Polubienia
- 8
- Pobrania
- 67
- Wydruki
- 0
- Wyświetlenia
- 1074
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Photo & Video
- Licencja
- Creative Commons — Attribution
Topcon is a highly respected Japanese optical company now known for opthalmic equipment, but for a while they made cameras and lenses. The Topcon RE lenses, which use a slightly modified Exakta mount, are exceptionally good. However, Topcon also had a budget line, the UV Topcors. The UV lenses are better than average performers, but neither as fast nor as sharp as the RE lenses. The UV name refers to a coating intended to block ultraviolet light, but many people misunderstand it as meaning the lenses were designed to photograph UV light. There is also difficulty adapting UV lenses to other mounts because the lenses do not have an aperture ring, but rely on an internal coupler to provide aperture control from a ring on the body. The result of all that is UV Topcor lenses being dramatically undervalued: I bought a bunch for about $6/lens!
There have been commercial adapters, but they're rare and expensive. The most common approach is to build an adapter using the mount taken from a Uni, Unirex, or IC-1 camera, but I don't advocate wrecking antique cameras. Thus, the adapter I created is entirely 3D printed, yet it provides a roughly-calibrated aperture control ring. Note that this adapter is a better fit on the A7II-style all-metal E/FE mounts; it's slightly loose on the original NEX E mount.
The first three photos show the adapter on an A7 with 50mm f/2, 100mm f/4, and 200mm f/4 UV Topcors. The last group of photos are taken with various UV Topcors using this adapter on an A7RII. Resolution is probably better suited to 24MP than 42MP full frame, but the lenses have a very pleasant 1960s-style rendering -- certainly way better than one would expect for a $6 lens. My biggest disappointment is that, like many 1960s lenses, they don't focus very close; the last shot required using a short extension tube.
Print Settings
Printer Brand:
Anycubic
Printer:
Kossel
Rafts:
No
Supports:
Yes
Resolution:
0.25mm or finer
Infill:
25% or more
Filament: generic PLA, Silk PLA Black, Silver
Notes:
There are three parts to be printed separately, although one of the STLs shows what they look like assembled.
The core has paths to allow the aperture ring to rotate appropriately and includes the UV Topcor bayonet. It is printed in Black PLA without additional supports, although there are some thin supports built-into the model for the slot that allows coupling with the lens aperture linkage. Print it is the orientation of the individual STL file, with the bayonet at the top.The aperture ring is also printed in Black PLA, but you will need to enable support for the small bar that couples to the aperture linkage.
The body is printed in Silver Silk PLA to approximately match the two-tone style of the UV Topcors. It is printed without supports, oriented with the E bayonet at the top.
Post-Printing
After the parts have been printed, remove any support material and other 3D-printing artifacts (e.g., strings or bumps).
Although not strictly necessary, I like to do a bit of painting -- as is shown in the fourth photo. Fill the two mount-alignment holes with red acrylic paint to improve visibility. A PLA-on-PLA interface will tend to stick, so I like to apply water-based clear polyurethane to any parts that move against each other as a sort of permanent lubricant. Finally, I also like to prevent potential reflections by painting the inside of the adapter with Black 2.0; it's an excellent light-absorbing finish.
To assemble the pieces, mount the core on a UV Topcor lens and let it click into the lens lock. Now orient the aperture ring so that the numbers are in the same orientation as the numbering on the lens and slide the ring over the core. Once the ring is flush against the back of the lens, it should freely rotate through the aperture settings f/2 through f/22; note that f/2 is the fastest possible aperture for UV lenses, an f/4 UV Topcor will still be at f/4 when the aperture ring is set wider than f/4. Next side the body over the core to be flush against the aperture ring.
To make this assembly permanent, you could use glue to hold the core and body together, but I prefer to weld them together. Welding is done using a soldering iron to melt parts together, possibly adding a little material. With the front of the lens facing down on a table, tack the body and core together by holding your soldering iron against the body bumps that are at the top of the groves in the core. The adapter design is deliberately slightly short, however, if you temporarily place shims between the aperture ring and body before soldering, you can solder the parts together with the precise length desired; once welded together, the shims can be removed. I like to paint over the weld with Black 2.0 to ensure no reflections.
Category: Camera